- Subscribe to RSS Feed
- Bookmark
- Subscribe
- Printer Friendly Page
- Report Inappropriate Content
- Adtran Support Community
- :
- Documentation
- :
- Intellifi
- :
- Intellifi MeshView
- :
- MeshView Release Notes
MeshView Release Notes
MeshView Release Notes
The following outlines the features, fixes, and errata included in the specified release version of MeshView.
MeshView Release 10.40.0
Released: July 3, 2024
Features
| Ticket | Release Notes |
|---|---|
|
FT-2714 |
The behavior of modal dialogs gathering user input has been made more consistent, accepting both enter and a button press to accept input and close the dialog. |
|
FT-3278 |
MeshView now returns to the previous page if a user is logged out due to inactivity. |
|
FT-3528 |
Aligned columns for Wi-Fi data in Device views. |
|
FT-3642 |
Improved formatting to show hidden arrows for accordion expanders. |
Fixes
| Ticket | Release Notes |
|---|---|
|
FT-3536 |
FIxed an issue where the tooltip for events on charts may show the value as undefined. |
|
FT-3698 |
Fixed an issue preventing capability tooltip from displaying for a 6GHz radio. |
|
FT-3786 |
Fixed an issue where 802.11n was omitted from the 5 GHz radio capabilities |
|
FT-3840 |
Fixed an issue that caused the Node Capabilities to not appear on first use. |
Errata
| Ticket | Release Notes |
|---|---|
|
FT-953 |
For networks with large number of end-user devices, the device page may get sluggish. |
|
FT-1072 |
The Topology diagram does not currently support full screen mode. |
|
FT-1081 |
In rare instances, the time axis values of some charts may be shifted 15 minutes left or right. |
|
FT-1087 |
The Advanced view takes a long time to load when the premises has a large event history. |
|
FT-1139 |
Occasionally, MeshView shows an anomaly on the airtime charts (the chart goes well above 100%). |
|
FT-1172 |
For some screen sizes and resolutions, MeshVew cards sometimes display with horizontal scrolling. |
|
FT-1198 |
Sometimes backhaul links are drawn over user devices. |
|
FT-1227 |
When unpausing a device, the Topology view still shows the pause icon over devices. Workaround: navigate out and back to the Topology view. |
|
FT-3745 |
Change error message to non-generic text in devices screen. |
MeshView Release 10.39.0
Released: June 24, 2024
Features
| Ticket | Release Notes |
|---|---|
|
FT-810 |
The Wi-Fi capability for each radio on a node is now displayed as a tool tip in the node Network Information panel. |
|
FT-3028 |
For nodes with firmware 12.6.2.1 or later, charts have been added to show the percentage of time that each Wi-Fi radio has total airtime above 80%. |
|
FT-3118 |
Backhaul (BH) Channel Change events are now shown on Uplink and Radio Airtime charts. |
|
FT-3835 |
The Node inventory table on the Admin -> Nodes tab has been updated and now shows all nodes in a tenant's inventory, whether the node has previously contacted the cloud or not. |
Fixes
| Ticket | Release Notes |
|---|---|
|
FT-3505 |
Filters for the events table are no longer reset when the data is updated. |
|
FT-3527 |
Fixed an issue where only a portion of the available manifests were shown in the Tenants Details card. |
|
FT-3536 |
FIxed an issue where the tooltip for events on charts may show the value as undefined. |
Errata
| Ticket | Release Notes |
|---|---|
|
FT-953 |
For networks with large number of end-user devices, the device page may get sluggish. |
|
FT-1072 |
The Topology diagram does not currently support full screen mode. |
|
FT-1081 |
In rare instances, the time axis values of some charts may be shifted 15 minutes left or right. |
|
FT-1087 |
The Advanced view takes a long time to load when the premises has a large event history. |
|
FT-1139 |
Occasionally, MeshView shows an anomaly on the airtime charts (the chart goes well above 100%). |
|
FT-1172 |
For some screen sizes and resolutions, MeshVew cards sometimes display with horizontal scrolling. |
|
FT-1198 |
Sometimes backhaul links are drawn over user devices. |
|
FT-1227 |
When unpausing a device, the Topology view still shows the pause icon over devices. Workaround: navigate out and back to the Topology view. |
|
FT-3840 |
Upon first use of the app, the Node Capabilities may not appear when hovering over the Radio Band header. If the browser is refreshed it should work as intended. |
MeshView Release 10.38.0
Released: June 7, 2024
Features
| Ticket | Release Notes |
|---|---|
|
FT-825 |
Added Wi-Fi Band next to the Signal Strength icon on the Devices page. |
|
FT-3315 |
The Network (Guest vs Primary), Radio, and AP Information is now shown in each device's Connected to section, in the Devices page. |
Fixes
| Ticket | Release Notes |
|---|---|
|
FT-927 |
When a user navigates to Admin > Nodes, the placeholder now displays the mobile account rather than the subscriber. |
|
FT-955 |
Updated the Firmware Labels table with the following changes:
|
|
FT-2402 |
Fixed an issue where in some charts displaying Download/Upload or Receive/Transmit, the rendered order of the data series and their legends were backwards. |
|
FT-2860 |
Manifest lists are now sorted based on modified date. The most recently modified manifest should be at the top of the manifest selector dropdown. |
|
FT-2939 |
Improved color-contrast on charts. |
|
FT-3083 |
Fixed an issue that was causing the Serial tooltip to display Address instead of MAC. |
|
FT-3089 |
Icon replaced for SDG-8610. |
|
FT-3097 |
Fixed an issue where an empty pop-up message was shown when removing a satellite from the nodes page. |
|
FT-3133 |
Fixed issue where signal information was not displaying correctly in the connection path. |
|
FT-3224 |
Fixed an issue where a corrupt capabilities file was produced when a user changed the premises of a controller. |
|
FT-3266 |
Introduced enhancements to the text that displays when the user hovers over the Speed Test Events tooltip. |
|
FT-3272 |
Fixed an issue in Mobile Account where the Add Controller modal could freeze if the MAC address was not entered with colon separators. |
|
FT-3418 |
Fixed an issue where the application was unresponsive when selecting the device Connection Path. |
|
FT-3480 |
Fixed an issue where the Connection Path would open an empty modal in rare instances. |
|
FT-3627 |
Introduced enhancements to the text that displays when the user hovers over the Wi-Fi Events tooltip. |
Errata
| Ticket | Release Notes |
|---|---|
|
FT-953 |
For networks with large number of end-user devices, the device page may get sluggish. |
|
FT-1072 |
The Topology diagram does not currently support full screen mode. |
|
FT-1081 |
The newest data point does not match the date on the x-axis for the telemetry charts. |
|
FT-1087 |
The Advanced view takes a long time to load when the premises has a large event history. |
|
FT-1139 |
Occasionally, MeshView shows an anomaly on the airtime charts (the chart goes well above 100%). |
|
FT-1172 |
For some screen sizes and resolutions, MeshVew cards sometimes display with horizontal scrolling. |
|
FT-1194 |
If a user is in Nodes view and a new data point arrives, a data point that has a future time may be shown on the 24h or 7day chart. |
|
FT-1198 |
Sometimes backhaul links are drawn over user devices. |
|
FT-1227 |
When unpausing a device, the Topology view still shows the pause icon over devices. Workaround: navigate out and back to the Topology view. |
MeshView Release 10.37.0
Released: May 24, 2024
Features
| Ticket | Release Notes |
|---|---|
|
FT-3132 |
Added the capability to view the connection path between a device and the internet from the Devices view. |
Fixes
| Ticket | Release Notes |
|---|---|
|
FT-988 |
Fixes a problem that resulted in an unexpected error when the user navigates to the Premises View and there is no Controller attached. |
|
FT-1071 |
Error message is now more informative response improved when a user attempts to extend a Virtual Field Technician tunnel beyond 7 days. |
|
FT-1272 |
Fixed a bug that caused incorrect columns to be shown in the downloaded events file. |
Errata
| Ticket | Release Notes |
|---|---|
|
FT-953 |
For networks with large number of end-user devices, the device page may get sluggish. |
|
FT-1072 |
The Topology diagram does not currently support full screen mode. |
|
FT-1081 |
The newest data point does not match the date on the x-axis for the telemetry charts. |
|
FT-1087 |
The Advanced view takes a long time to load when the premises has a large event history. |
|
FT-1139 |
Occasionally, MeshView shows an anomaly on the airtime charts (the chart goes well above 100%). |
|
FT-1172 |
For some screen sizes and resolutions, MeshVew cards sometimes display with horizontal scrolling. |
|
FT-1194 |
If a user is in Nodes view and a new data point arrives, a data point that has a future time may be shown on the 24h or 7day chart. |
|
FT-1198 |
Sometimes backhaul links are drawn over user devices. |
|
FT-1227 |
When unpausing a device, the Topology view still shows the pause icon over devices. Workaround: navigate out and back to the Topology view. |
|
FT-1265 |
An Unexpected Error may be displayed when accessing the Devices page if a premises has no end-user devices in its history. |
|
FT-3224 |
In the event a user changes the premises to a controller which produces a corrupt capabilities file, the user is shown an uncaught error. |
|
FT-3272 |
On the Mobile Account page, the Add Controller modal may freeze if MAC address is not entered with ":" separators. |
|
FT-3480 |
In rare instances, the Device Connection Path pop-up on the Devices UI will not display any info. |
MeshView Release 10.36.0
Released: May 9, 2024
Fixes
| Ticket | Release Notes |
|---|---|
|
FT-1022 |
Fixed an issue with the display of Speedtest results that would hang if the result returned was 0. |
|
FT-1057 |
Improved the display of the server URL in the last Speedtest result. |
|
FT-1206 |
Fixed an issue where the uplink status color in the Premises screen Nodes card was incorrect. |
|
FT-1218 |
Fixed an issue where mouse-based paste of Speedtest server was not accepted until keyboard input was received. |
|
FT-1223 |
Fixed an issue where undefined values were displayed for offline devices. |
|
FT-1274 |
Fixed an issue which prevented renaming a device to include parenthesis and space characters. |
|
FT-2410 |
Improved error message for a link to a Meshview page which includes an invalid accountid. |
|
FT-2950 |
Fixed several small issues affecting the calculation and display of Wi-Fi speeds and modulation parameters. |
|
FT-2951 |
Fixed an issue that caused the max PHY rate to not be displayed in the devices view for 802.11a/b/g only devices. Note that SmartOS 12.5.x.x is required for these values to be displayed. |
|
FT-2973 |
Fixed an issue that caused infinite polling when a new mobile account contains a '+' symbol. |
|
FT-3135 |
When Guest APs are configured, series for these APs now are shown on the AP Throughput charts on the Nodes page. |
|
FT-3140 |
Wording related to Claiming and Unclaiming of a Controller by a Mobile Account and Adding and Removing a Satellite from a Controller's Network was updated to improve consistency and reduce confusion. |
MeshView Release 10.35.0
Released: April 25, 2024
Features
| Ticket | Release Notes |
|---|---|
|
FT-2934 |
Device view now shows the maximum possible Wi-Fi PHY rate and associated parameters as provided by the device in the association request. SmartOS 12.5.1.1 or newer is required to show maximum PHY rate for 802.11a/b/g/n-only devices. |
|
FT-2936 |
Network Status now shows both downstream and upstream rates and quality is colored relative to service plan rate info from Mosaic One if it exists. |
|
FT-2937 |
Meshview now displays a What's New popup the first time accessed when a new version is released. |
|
FT-2938 |
In the Admin/Jobs table, entries show additional details when selected. |
Fixes
| Ticket | Release Notes |
|---|---|
|
FT-928 |
Fixed an issue where the number of devices would sometimes show as a negative number. |
|
FT-933 |
Fixed an issue where a new search was not performed if the button was pressed multiple times without changing the input text. |
|
FT-938 |
Fixed an issue where a spinner would appear on all buttons instead of the one selected for action. |
|
FT-961 |
Fixed an issue where "no results found" would briefly display when accessing the advanced screen. |
|
FT-1269 |
Fixed an infinite spinner that would occur in the events table if no events were present. |
|
FT-1322 |
Fixed an issue in NPM IP Package vulnerable to Server-side Request Forgery (SSRF) by upgrading newer version. |
Errata
| Ticket | Release Notes |
|---|---|
|
FT-1072 |
The Topology diagram does not currently support full screen mode. |
|
FT-1081 |
The newest data point does not match the date on the x-axis for the telemetry charts. |
|
FT-1087 |
The Advanced view takes a long time to load when the premises has a large event history. |
|
FT-1124 |
Offline/Inactive Satellites are not being displayed in the Topology View. |
|
FT-1139 |
Occasionally, MeshView shows an anomaly on the airtime charts (the chart goes well above 100%). |
|
FT-1172 |
For some screen sizes and resolutions, MeshVew cards sometimes display with horizontal scrolling. |
|
FT-1194 |
If a user is in Nodes view and a new data point arrives, a data point that has a future time may be shown on the 24h or 7day chart. |
|
FT-1198 |
Sometimes backhaul links are drawn over user devices. |
|
FT-1227 |
When unpausing a device, the Topology view still shows the pause icon over devices. Workaround: navigate out and back to the Topology view. |
MeshView Release 10.33.0
Released: March 28, 2024
Fixes
| Ticket | Release Notes |
|---|---|
|
IMI-2809 |
Fixed an issue when tenants are changed the information information displayed was not correct. |
|
IMI-2796 |
Fixed an issue that was causing the date filter on speed test history not be displayed correctly. |
|
IMI-2795 |
Added an error message when the user tries to force change password. |
|
IMI-2791 |
Fixed issue when a helpdesk or CSR roles pastes a URL to navigate to the admin view a page not found page was displayed. |
|
IMI-2749 |
Fixed an issue with Virtual Field Technician not opening a tab. |
|
IMI-2742 |
Fixed an issue with the delete action once a tunnel was extended. |
|
IMI-2735 |
Fixed an issue with disabled buttons being displayed in the Advanced Mobile Account. |
|
IMI-2727 |
Fixed an issue when changing the firmware label at the Advanced view Firmware tab and instantly moving to another tab and then coming back to the Firmware tab the firmware label field shows "none" as the selected. |
|
IMI-2719 |
Fixed an issue with an unexpected error with Autorefresh. |
|
IMI-2590 |
Fixed an issue with the data not being updated when the user attaches a controller to a mobile account. |
|
IMI-1943 |
Fixed an issue with the delete action once a tunnel was created. |
Errata
| Ticket | Release Notes |
|---|---|
|
IMI-2791 |
Fixed issue when a helpdesk or CSR roles pastes a URL to navigate to the admin view a page not found page was displayed. |
|
IMI-2775 |
From time to time, MeshView shows an anomaly on the airtime charts (the chart goes well above 100%) |
|
IMI-1137 |
The advanced view takes a long time to load when the premises has a large event history. |
|
IMI-1135 |
The newest data point does not match the date on the x-axis for the telemetry charts. |
|
IMI-1120 |
The Topology diagram does not support full screen mode today. |
|
IMI-1118 |
Sometimes backhaul links are drawn over user devices. |
|
IMI-1115 |
When user is on the 24hs or 7days and a new data point arrives, a data point that has a future time may be shown. |
|
IMI-801 |
When unpausing a device, the Topology View still shows the pause icon over devices. |
|
IMI-302 |
Offline/inactive Satellites are not being displayed in the Topology View. |
|
IMI-113 |
For some screen sizes and resolutions, MeshVew cards sometimes end up with horizontal scrolling. |
MeshView Release 10.32.0
Released: March 19, 2024
Features
| Ticket | Release Notes |
|---|---|
|
SDGP-1455 |
MeshView now shows the tunnel URL and SSH connection information in the Configuration View. |
Errata
| Ticket | Release Notes |
|---|---|
|
IMI-2791 |
Fixed issue with updated dependency - oidc-auth-extension version should be "19.3.0" |
|
IMI-2775 |
From time to time, MeshView shows an anomaly on the airtime charts (the chart goes well above 100%) |
|
IMI-1137 |
The advanced view takes a long time to load when the premises has a large event history. |
|
IMI-1135 |
The newest data point does not match the date on the x-axis for the telemetry charts. |
|
IMI-1120 |
The Topology diagram does not support full screen mode today. |
|
IMI-1118 |
Sometimes backhaul links are drawn over user devices. |
|
IMI-1115 |
When user is on the 24hs or 7days and a new data point arrives, a data point that has a future time may be shown. |
|
IMI-801 |
When unpausing a device, the Topology View still shows the pause icon over devices. |
|
IMI-302 |
Offline/inactive Satellites are not being displayed in the Topology View. |
|
IMI-113 |
For some screen sizes and resolutions, MeshVew cards sometimes end up with horizontal scrolling. |
MeshView Release 10.31.0
Released: March 14, 2024
Features
| Ticket | Release Notes |
|---|---|
|
SDGP-956 |
MeshView Node Inventory management now supports bulk upload of MAC addresses, bulk delete of MAC addresses, and Download Node report (including nodes that have not been onboarded yet). |
Fixes
| Ticket | Release Notes |
|---|---|
|
IMI-2745 |
Fixed an icon shown for unknown wired devices. |
|
IMI-2743 |
Added the bootComplete events to Nodes events. |
|
IMI-2731 |
Fixed an unexpected error when trying to read the Chromecast devices icon. |
|
IMI-2699 |
Fixed issue in topology were devices without upHost were shown. |
|
IMI-2668 |
Fixed an unexpected error on devices page. |
|
IMI-2657 |
Fixed an issue of incorrect picture displaying for the some models. |
|
IMI-2605 |
Fixed an issue were user selection for showing and hiding Events series was being overwritten after zooming in/out. |
|
IMI-2582 |
Fixed an issue were unexpected error appeared on configuration page when Refresh button is selected. |
|
IMI-2490 |
Fixed an issue when a user device is selected of getting redirected to the bottom of the list instead of the selected user device. |
|
IMI-1841 |
Fixed an issue on the UI tab on the About menu popup screen to show the published environment info with the software build number between parenthesis. |
Errata
| Ticket | Release Notes |
|---|---|
|
IMI-2791 |
Fixed issue with updated dependency - oidc-auth-extension version should be "19.3.0" |
|
IMI-2775 |
From time to time, MeshView shows an anomaly on the airtime charts (the chart goes well above 100%) |
|
IMI-1137 |
The advanced view takes a long time to load when the premises has a large event history. |
|
IMI-1135 |
The newest data point does not match the date on the x-axis for the telemetry charts. |
|
IMI-1120 |
The Topology diagram does not support full screen mode today. |
|
IMI-1118 |
Sometimes backhaul links are drawn over user devices. |
|
IMI-1115 |
When user is on the 24hs or 7days and a new data point arrives, a data point that has a future time may be shown. |
|
IMI-801 |
When unpausing a device, the Topology View still shows the pause icon over devices. |
|
IMI-302 |
Offline/inactive Satellites are not being displayed in the Topology View. |
|
IMI-113 |
For some screen sizes and resolutions, MeshVew cards sometimes end up with horizontal scrolling. |
MeshView Release 10.30.0
Released: February 29, 2024
Features
| Ticket | Release Notes |
|---|---|
|
SDGP-979 |
MeshView now supports overlaying selected events on top of the different Node and Device charts. |
|
MH-1218 |
Intellifi Care Integration has been released. |
Fixes
| Ticket | Release Notes |
|---|---|
|
IMI-2720 |
Fixed an issue with Fingerprint Class not working with upper case values. |
|
IMI-2719 |
Fixed an issue with an unexpected error with Autorefresh. |
|
IMI-2676 |
Added icon information about download nodes on Admin/Nodes. |
|
IMI-2674 |
Fixed an issue where all nodes in Admin/Nodes view were incorrectly shown. |
|
IMI-2671 |
Fixed an issue when tenants are changed the information between them is not correct. |
|
IMI-2667 |
Added expected names for wan events: wan/up, wan/down |
|
IMI-2665 |
Updated the expected names for BHTopologyChange event to BHTopoChange |
|
IMI-2664 |
Fixed that the network status was not updated when changing premises on the selector. |
|
IMI-2662 |
Fixed that the tunnel expiration time label was not updated. |
|
IMI-2661 |
Updated the expected names for wan events: |
|
IMI-2656 |
Fixed an issue when quickly selecting the new snapshot button located on the advanced page in the support snapshot tab an unexpected error appears. |
|
IMI-2616 |
Fixed an issue with incorrect link on wired/wireless clients on topology. |
|
IMI-2614 |
Fixed an issue with the Tunnel not being updated in UI when deleted. |
|
IMI-2155 |
Fixed an issue triggered when the user tries to navigate the system referencing a recently unclaimed controller. |
|
IMI-1860 |
Fixed an issue following a factory reset of the controller an infinite loader showed up in the nodes screen. |
|
IMI-1846 |
Fixed that when factory reset happened in parallel, the auto-refresh showed outdated info. |
Errata
| Ticket | Release Notes |
|---|---|
|
IMI-2723 |
Incorrect link on wired/wireless clients on topology |
|
IMI-1137 |
The advanced view takes a long time to load when the premises has a large event history. |
|
IMI-1135 |
The newest data point does not match the date on the x-axis for the telemetry charts. |
|
IMI-1120 |
The Topology diagram does not support full screen mode today. |
|
IMI-1118 |
Sometimes backhaul links are drawn over user devices. |
|
IMI-1115 |
When user is on the 24hs or 7days and a new data point arrives, a data point that has a future time may be shown. |
|
IMI-801 |
When unpausing a device, the Topology View still shows the pause icon over devices. |
|
IMI-302 |
Offline/inactive Satellites are not being displayed in the Topology View. |
|
IMI-113 |
For some screen sizes and resolutions, MeshVew cards sometimes end up with horizontal scrolling. |
MeshView Release 10.28.0
Released: February 15, 2024
Fixes
| Ticket | Release Notes |
|---|---|
|
IMI-2600 |
Fixed an issue that causes an infinite loading when creating a mobile account in the admin screen. |
|
IMI-1711 |
Fixed an issue with an online controller that has an offline satellite the extension shows an incorrect message. |
Errata
| Ticket | Release Notes |
|---|---|
|
IMI-2791 |
Fixed issue with updated dependency - oidc-auth-extension version should be "19.3.0" |
|
IMI-2775 |
From time to time, MeshView shows an anomaly on the airtime charts (the chart goes well above 100%) |
|
IMI-1137 |
The advanced view takes a long time to load when the premises has a large event history. |
|
IMI-1135 |
The newest data point does not match the date on the x-axis for the telemetry charts. |
|
IMI-1120 |
The Topology diagram does not support full screen mode today. |
|
IMI-1118 |
Sometimes backhaul links are drawn over user devices. |
|
IMI-1115 |
When user is on the 24hs or 7days and a new data point arrives, a data point that has a future time may be shown. |
|
IMI-801 |
When unpausing a device, the Topology View still shows the pause icon over devices. |
|
IMI-302 |
Offline/inactive Satellites are not being displayed in the Topology View. |
|
IMI-113 |
For some screen sizes and resolutions, MeshVew cards sometimes end up with horizontal scrolling. |
MeshView Release 10.27.1
Released: February 8, 2024
Fixes
| Ticket | Release Notes |
|---|---|
|
IMI-2613 |
Fixed an issue with Tunnel port numbers being unintentionally redirected. |
Errata
| Ticket | Release Notes |
|---|---|
|
IMI-2791 |
Fixed issue with updated dependency - oidc-auth-extension version should be "19.3.0" |
|
IMI-2775 |
From time to time, MeshView shows an anomaly on the airtime charts (the chart goes well above 100%) |
|
IMI-1137 |
The advanced view takes a long time to load when the premises has a large event history. |
|
IMI-1135 |
The newest data point does not match the date on the x-axis for the telemetry charts. |
|
IMI-1120 |
The Topology diagram does not support full screen mode today. |
|
IMI-1118 |
Sometimes backhaul links are drawn over user devices. |
|
IMI-1115 |
When user is on the 24hs or 7days and a new data point arrives, a data point that has a future time may be shown. |
|
IMI-801 |
When unpausing a device, the Topology View still shows the pause icon over devices. |
|
IMI-302 |
Offline/inactive Satellites are not being displayed in the Topology View. |
|
IMI-113 |
For some screen sizes and resolutions, MeshVew cards sometimes end up with horizontal scrolling. |
MeshView Release 10.27.0
Released: February 1, 2024
Features
| Ticket | Release Notes |
|---|---|
|
SDGP-1221 |
Added support for pre-provisioning mobile accounts in MeshView Admin View |
|
SDGP-962 |
MeshView now supports adding, editing, and deleting mobile accounts. |
Fixes
| Ticket | Release Notes |
|---|---|
|
IMI-2584 |
Fixed issue with attribute selection in endpoints. |
|
IMI-2493 |
Fixed a problem with autorefresh that affects screen scrolling. |
|
IMI-2470 |
Fixed an issue with infinite load spinner being displayed when user navigates to Advanced View on Firmware tab. |
|
IMI-2397 |
Fixed an issue that causes the polling to execute 10 times before finishing the create mobile account process. |
|
IMI-2396 |
Fixed an issue with the polling in the mobile account not stopping if there isn't a first name and last name. |
|
IMI-2395 |
Fixed an issue on the Mobile Accounts tab of the Admin page if the admin user edited several mobile accounts before the previous data update was completed server-side, there was a continuous request cycle that was not finished before the user moved onto updating the next account. |
|
IMI-2391 |
Fixed an issue with the delete premises popup not showing the premises name. |
|
IMI-2388 |
Fixed an issue with some validations like pattern and length being missed on the edit account form. |
|
IMI-2386 |
Fixed an issue when entering the mobile accounts tab the subscriber's endpoint was called twice. |
|
IMI-2351 |
Fixed an issue where Speedtest card was not visible when controller had no speedtests. |
|
IMI-2344 |
Fixed an issue with Profiles unexpected error when Access Schedule is selected. |
|
IMI-2311 |
Fixed an issue where the uplink color disappears when entering premises view. |
|
IMI-2304 |
Fixed an issue with the premises data usage chart name not being updated. |
|
IMI-2176 |
Fixed an issue when a user attaches a controller the messaging was not updated. |
|
IMI-1821 |
Fixed an issue where telemetry data was not displayed after a node is unclaimed. |
Errata
| Ticket | Release Notes |
|---|---|
|
IMI-2791 |
Fixed issue with updated dependency - oidc-auth-extension version should be "19.3.0" |
|
IMI-2775 |
From time to time, MeshView shows an anomaly on the airtime charts (the chart goes well above 100%) |
|
IMI-1137 |
The advanced view takes a long time to load when the premises has a large event history. |
|
IMI-1135 |
The newest data point does not match the date on the x-axis for the telemetry charts. |
|
IMI-1120 |
The Topology diagram does not support full screen mode today. |
|
IMI-1118 |
Sometimes backhaul links are drawn over user devices. |
|
IMI-1115 |
When user is on the 24hs or 7days and a new data point arrives, a data point that has a future time may be shown. |
|
IMI-801 |
When unpausing a device, the Topology View still shows the pause icon over devices. |
|
IMI-302 |
Offline/inactive Satellites are not being displayed in the Topology View. |
|
IMI-113 |
For some screen sizes and resolutions, MeshVew cards sometimes end up with horizontal scrolling. |
MeshView Release 10.24.1
Released: January 19, 2024
Fixes
| Ticket | Release Notes |
|---|---|
|
IMI-2492 |
Fixed an issue with unexpected error message, "Cannot destructure property 'chart' of 'Ct' as it is undefined. is displayed on Events History chart. |
|
IMI-2475 |
Fixed an issue when the user searches for a node through it´s MAC address, then clicks on it, goes to topology and tries to get redirected to nodes view by clicking on the node at the topology chart. An unexpected error showed up and the topology view page turned all white. |
|
IMI-2474 |
Fixed an issue with an unexpected error when the user searched for an offline/online controller or an online satellite by the MAC address then clicks on the MAC and goes to the advanced view. |
|
IMI-2473 |
Fixed an issue where the Events chart showed space for 7 days of events even when there were less. |
Errata
| Ticket | Release Notes |
|---|---|
|
IMI-2791 |
Fixed issue with updated dependency - oidc-auth-extension version should be "19.3.0" |
|
IMI-2775 |
From time to time, MeshView shows an anomaly on the airtime charts (the chart goes well above 100%) |
|
IMI-1137 |
The advanced view takes a long time to load when the premises has a large event history. |
|
IMI-1135 |
The newest data point does not match the date on the x-axis for the telemetry charts. |
|
IMI-1120 |
The Topology diagram does not support full screen mode today. |
|
IMI-1118 |
Sometimes backhaul links are drawn over user devices. |
|
IMI-1115 |
When user is on the 24hs or 7days and a new data point arrives, a data point that has a future time may be shown. |
|
IMI-801 |
When unpausing a device, the Topology View still shows the pause icon over devices. |
|
IMI-302 |
Offline/inactive Satellites are not being displayed in the Topology View. |
|
IMI-113 |
For some screen sizes and resolutions, MeshVew cards sometimes end up with horizontal scrolling. |
MeshView Release 10.24.0
Released: January 19, 2024
Fixes
| Ticket | Release Notes |
|---|---|
|
IMI-2410 |
Fixed an issue on the Configuration screen when the user had an open virtual field technician tunnel open and tried to extend the remaining time by clicking on the dropdown the app showed an error on a toast message at the bottom. |
|
IMI-2387 |
Fixed an issue when the user edits a mobile account the filters are removed and all the mobile accounts list is displayed. |
|
IMI-2383 |
Fixed an issue of a deleted account being shown in the table results after a successful delete and navigation. |
|
IMI-2381 |
Fixed a navigation issue caused by query parameters. |
|
IMI-2348 |
Fixed an issue when searching a mobile account in the Mobile Accounts tab of the Admin view, provided the search term contained an allowed special character (for example searching for an email with @), it was being sent unencoded making it impossible to match accounts. |
|
IMI-2347 |
Fixed that the modal for deleting an account was not closed after the delete was successful or if there was an error. |
|
IMI-2345 |
Fixed an issue when zooming in by drag and drop on the speedtest chart on the top left of the chart an unexpected error appears. |
|
IMI-2341 |
Fixed an issue where the telemetry endpoint was called multiple times. |
|
IMI-2306 |
Fixed an issue where Advanced firmware label was being incorrectly displayed. |
|
IMI-2303 |
Zoom info icon and tooltip were missing from the Events' chart zoom label. |
|
IMI-2302 |
Fixed an issue where the nodes charts didn't load after change premise in the nodes view. |
|
IMI-2295 |
Disabled the delete button when the user only has one premises. |
|
IMI-2285 |
Fixed an issue that causes the cut-through label to appear on premises without cut-through open. |
|
IMI-2270 |
Displaying o'clock time (:00) for the labels of the x-axis ticks instead of the exact time of the event. |
|
IMI-2224 |
The styling of the Configuration screen cards was changed so the appearance matches other screens of the application (Devices, Nodes) |
|
IMI-2178 |
Fixed an issue with redirection inside MeshView that resulted in the Node or Device view opening but not opening the corresponding accordion. |
|
IMI-2169 |
Fixed the size of the online status chart to cover the full modal width when the screen is wider. |
|
IMI-2167 |
Fixed an issue with the offline toast not being displayed when the user turns off the controller and clicks the refresh button. |
|
IMI-2150 |
Fixed an issue with a wrong validation error being shown in the attach controller form when there was not an error. |
|
IMI-1979 |
Fixed an issue where some endpoints were called several times. |
|
IMI-1824 |
Fixed an issue with Attach button always enabled when there were validation errors. |
|
IMI-1806 |
Fixed an issue that causes the device's endpoint to be called twice on multiple screens. |
|
IMI-1801 |
Fixed an issue with the success toast being shown before the MAC appeared on the premises table. |
Errata
| Ticket | Release Notes |
|---|---|
|
IMI-2791 |
Fixed issue with updated dependency - oidc-auth-extension version should be "19.3.0" |
|
IMI-2775 |
From time to time, MeshView shows an anomaly on the airtime charts (the chart goes well above 100%) |
|
IMI-1137 |
The advanced view takes a long time to load when the premises has a large event history. |
|
IMI-1135 |
The newest data point does not match the date on the x-axis for the telemetry charts. |
|
IMI-1120 |
The Topology diagram does not support full screen mode today. |
|
IMI-1118 |
Sometimes backhaul links are drawn over user devices. |
|
IMI-1115 |
When user is on the 24hs or 7days and a new data point arrives, a data point that has a future time may be shown. |
|
IMI-801 |
When unpausing a device, the Topology View still shows the pause icon over devices. |
|
IMI-302 |
Offline/inactive Satellites are not being displayed in the Topology View. |
|
IMI-113 |
For some screen sizes and resolutions, MeshVew cards sometimes end up with horizontal scrolling. |
MeshView Release 10.16.0
Released: January 19, 2024
Fixes
| Ticket | Release Notes |
|---|---|
|
IMI-2290 |
Fixed an issue with pan on the Node Event History chart not being enabled on the y-axis. |
|
IMI-2286 |
Fixed unexpected error in profiles screen. |
|
IMI-2272 |
Added error message "No Events data found for node" when there is no Event's file available. |
|
IMI-2271 |
Added hostname to Node Event History chart. |
|
IMI-2269 |
Fixed an issue when there was more than one node on the premises, filters are applied to both instances of the chart. |
|
IMI-2268 |
Fixed an issue where Events were not filtered based on the node that was selected. |
|
IMI-2266 |
Fixed an issue with speed test number format. |
|
IMI-2265 |
Fixed an issue to bold the last updated label when the user navigates to the autorefresh pages. |
|
IMI-2258 |
Fixed an unexpected error that was displayed when the user unclaims the controller in parallel and clicks the refresh button. |
|
IMI-2181 |
Fixed an issue with the wireless/wired icon flickering when the user stays in the devices view until the auto refresh appears. |
|
IMI-2166 |
Fixed the issue where the refresh button did not appear in certain scenarios. |
|
IMI-2162 |
Fixed an issue that was causing the endpoints in Configuration Page, to be called twice. |
|
IMI-2159 |
Fixed an issue with the refresh button not working properly with parallel navigation. |
|
IMI-2149 |
Fixed an issue with online/offline icon position. |
|
IMI-2103 |
Fixed an issue that was causing endpoints to be called on an empty premises when clicking on the refresh button. |
|
IMI-2052 |
Fixed an issue where unnecessary endpoints were called after the pause time of a profile expired. |
|
IMI-2023 |
Fixed an issue where Endpoints were called multiple times on every page. |
|
IMI-1995 |
Fixed an issue when there is a canceled request due to clicking different toggles too quickly. |
|
IMI-1976 |
Fixed an issue with information not being updated on the configuration view. |
|
IMI-1951 |
Fixed unexpected error with 12.1.3.1 satellites. |
|
IMI-1811 |
Fixed an issue with the color of the status indicator of the client devices in the Profiles screen turning black instead of green/red for online/offline when changing through the premises. |
|
IMI-1767 |
Fixed an issue in the Topology screen when a user device has internet access paused it was not possible to view the paused icon on the graph. |
|
IMI-1764 |
Fixed an issue with numbers not being displayed correctly on Network speed tool tip for numbers >1K. |
|
IMI-352 |
Fixed an issue when dragging and dropping the user devices through the different profiles in the Profiles screen that was causing the text to show with another font/style. |
Errata
| Ticket | Release Notes |
|---|---|
|
IMI-2791 |
Fixed issue with updated dependency - oidc-auth-extension version should be "19.3.0" |
|
IMI-2775 |
From time to time, MeshView shows an anomaly on the airtime charts (the chart goes well above 100%) |
|
IMI-1137 |
The advanced view takes a long time to load when the premises has a large event history. |
|
IMI-1135 |
The newest data point does not match the date on the x-axis for the telemetry charts. |
|
IMI-1120 |
The Topology diagram does not support full screen mode today. |
|
IMI-1118 |
Sometimes backhaul links are drawn over user devices. |
|
IMI-1115 |
When user is on the 24hs or 7days and a new data point arrives, a data point that has a future time may be shown. |
|
IMI-801 |
When unpausing a device, the Topology View still shows the pause icon over devices. |
|
IMI-302 |
Offline/inactive Satellites are not being displayed in the Topology View. |
|
IMI-113 |
For some screen sizes and resolutions, MeshVew cards sometimes end up with horizontal scrolling. |
MeshView Release 10.5.0
Released: December 7, 2023
Fixes
| Ticket | Release Notes |
|---|---|
|
MH-616 |
The Devices screen now allows each user device's card to be opened by clicking anywhere in the device area. |
|
IMI-2168 |
Fixed a problem that results in an unexpected error "Uncaught (in promise): ReferenceError: Cannot access 'nn' before initialization" when the user clicks on the Node icon of an online Controller in the Premises View and navigates to the Nodes View. |
|
IMI-2157 |
Fixed the MAC address being incorrectly shown when hovering the MAC on the Nodes card in the Premises view. |
|
IMI-2153 |
Fixed an unexpected error where the information for the previous premises was displayed. |
|
IMI-2152 |
Fixed a problem with HelpDesk users being able to see the attach action enabled and attach controllers. |
|
IMI-2144 |
Added icon for wired unknown devices. |
|
IMI-2108 |
Fixed an issue when the controller was offline by creating a cut-through. |
|
IMI-2105 |
Fixed the call of multiple endpoints from premises that are not needed in other screens. |
|
IMI-2102 |
Fixed an issue which prevented controllers without subscribers updating the data on the nodes screen for the autorefresh. |
|
IMI-2101 |
Fixed a problem with redirection inside MeshView that resulted in the Node or Device view opening but not opening the corresponding accordion. |
|
IMI-2094 |
Fixed a problem with the Profiles View that results in the Device icon not updating after the user updates the Device name (e.g. start with a Device with a generic icon and change the name to "printer", the icon should change to a printer icon). |
|
IMI-2093 |
Fixed a problem that results in the online/offline status of a Device not being updated upon refresh. |
|
IMI-2078 |
Fixed a problem with autorefresh that affects screen scrolling. |
|
IMI-2076 |
Fixed an issue where the title for some Telemetry charts was missing. |
|
IMI-2055 |
Fixed an issue regarding active access schedules on profiles where user cannot resume profiles that are paused due to an active access schedule. |
|
IMI-2053 |
Added a description when a profile is paused due to an active access schedule. |
|
IMI-2050 |
Fixed an issue where the information for the current account was not updated in the header section. |
|
IMI-2046 |
Fixed a problem that resulted in multiple calls executed and loaders displayed when the user attaches a controller to a subscriber that has more than one premises with attached controllers. |
|
IMI-2042 |
Fixed an issue where the Configuration screen UI sliding controls were not aligned to the texts on the card titles nor the labels at the side of the sliders. |
|
IMI-2040 |
Fixed a problem that results in the offline toaster not being displayed in the Advanced view when the user turns off the controller and clicks the "Refresh" button in this view. |
|
IMI-2034 |
Fixed a problem that results in an unexpected error "Uncaught (in promise): ReferenceError: Cannot access 'nn' before initialization" when the user clicks on the Node icon of an online Controller in the Premises View and navigates to the Nodes View. |
|
IMI-2026 |
Fixed an unexpected error that appears when the autorefresh appears after the controller is unclaimed. |
|
IMI-2025 |
Fixed an issue with the device showing incorrect information indicating it was subordinated to itself. |
|
IMI-2022 |
Fixed an issue where the user could see the message "no premises found" for an instant when navigating into the mobile account view. |
|
IMI-1988 |
Fixed a problem that results in the autorefresh not updating a Device name after the name has been changed by the user in some other View. |
|
IMI-1977 |
Fixed an issue where the MeshView title on the sidebar is not clickable. |
|
IMI-1916 |
Fixed a problem that causes the tunnel endpoints to be called across all the screens multiple times. |
|
IMI-1836 |
Fixed a problem with Topology that results in some icons not being rendered (e.g. printer), instead a generic phone icon is shown. |
|
IMI-1833 |
Fixes an issue where MeshView does not show the Offline toast message when a Node or Mobile Account is being watched and it goes offline. |
|
IMI-1209 |
Fixed a problem that prevents the company logo from being displayed in the Admin view of MeshView. |
|
IMI-1178 |
Fixed a problem when a profile is paused with an access schedule, the schedule information was not displayed correctly. |
|
IMI-754 |
Fixed a problem that results in MeshView displaying the wrong icon when the icon has been updated via the Mobile App. |
Errata
| Ticket | Release Notes |
|---|---|
|
IMI-2158 |
MeshView is not rendering tenant logos in the Admin view. |
|
IMI-1821 |
MeshView fails to display telemetry data after a node is unclaimed. |
|
IMI-1811 |
The color of the status indicator of the client devices in the Profiles screen turns black instead of green/red for online/offline when changing through the premises. |
|
IMI-1767 |
In the Topology screen, when a user device has its internet access paused it is not possible to view the paused icon on the graph. |
|
IMI-1137 |
The advanced view takes a long time to load when the premises has a large event history. |
|
IMI-1135 |
The newest data point does not match the date on the x-axis for the telemetry charts. |
|
IMI-1120 |
The Topology diagram does not support full screen mode today. |
|
IMI-1118 |
Sometimes backhaul links are drawn over user devices. |
|
IMI-1115 |
When user is on the 24hs or 7days and a new data point arrives, a data point that has a future time may be shown. |
|
IMI-801 |
When unpausing a device, the Topology View still shows the pause icon over devices. |
|
IMI-352 |
Dragging and dropping the user devices through the different profiles in the Profiles screen was causing the text to show with another font/style. |
|
IMI-302 |
Offline/inactive Satellites are not being displayed in the Topology View. |
|
IMI-113 |
For some screen sizes and resolutions, MeshVew cards sometimes end up with horizontal scrolling. |
MeshView Release 9.3.0
Released: November 9, 2023
Fixes
| Ticket | Release Notes |
|---|---|
|
IMI-1971 |
Fixes a problem with the "About" menu not showing the correct version. |
|
IMI-1969 |
Fixes a problem that results in the toggle controls disappearing form the Configuration view. |
|
IMI-1963 |
Fixes a problem that results in an unexpected error "Cannot convert undefined or null to object" |
|
IMI-1957 |
When the user expands the online status history chart and hovers it, the tooltip appears above the chart. |
|
IMI-1955 |
Sometimes the chart context menu appears and disappears. |
|
IMI-1897 |
Fixes a problem that results in some controllers not displaying telemetry data in the UI. |
|
IMI-1895 |
When the user selects an empty premises from the Premises (or other) Views using the drop-down selector, it is redirected to the search page with an error. |
|
IMI-1866 |
Fixes a problem that prevents a user form specifying a speedtest server for a Controller that has been onboard but not claimed. |
|
IMI-1864 |
Fixes a problem that results in an infinite loader when the user goes to the Advanced View and the Controller has no events to display |
|
IMI-1859 |
Fixes a problem that results in an unexpected error when the user executes an action and moves fast to another view |
|
IMI-1796 |
Fixes a problem that results in an unexpected error when the user navigates to the Premises View and there is no Controller attached |
|
IMI-1760 |
On occasions, the Uplink stats for a wired backhaul are not displayed in the Node View |
Errata
| Ticket | Release Notes |
|---|---|
|
IMI-2164 |
Unexpected error was removed when refreshing an empty premises |
|
IMI-2158 |
MeshView is not rendering tenant logos in the Admin view. |
|
IMI-2104 |
The Devices screen was reporting an unexpected error while staying on the screen while the data was updating on a premises that did not have an RG controller assigned. |
|
IMI-2042 |
The Configuration screen UI sliding controls were not aligned to the texts on the card titles nor the labels at the side of the sliders. |
|
IMI-1821 |
MeshView fails to display telemetry data after a node is un-claimed |
|
IMI-1137 |
The advanced view takes a long time to load when the premises has a large event history. |
|
IMI-1135 |
The newest data point does not match the date on the x-axis for the telemetry charts. |
|
IMI-1120 |
The Topology diagram does not support full screen mode today. |
|
IMI-1118 |
Sometimes backhaul links are drawn over user devices. |
|
IMI-1115 |
When user is on the 24hs or 7days and a new data point arrives, sometimes we're showing a data point that has a future time |
|
IMI-801 |
When unpausing a device, the Topology View still shows the pause icon over devices. |
|
IMI-754 |
The "guessed" device type was not using the device type selected on the Intellifi App |
|
IMI-302 |
Offline/inactive Satellites are not being displayed in the Topology View. |
|
IMI-113 |
For some screen sizes and resolutions, MeshVew cards sometimes end up with horizontal scrolling. |
MeshView Release 9.1.0
Released: October 19, 2023
Features
| Ticket | Release Notes |
|---|---|
|
SDGP-1314 |
MeshView topology now refreshes every 60 seconds without user intervention, |
|
SDGP-1230 |
MeshView now allows the ISP user to download a CSV file with event data. |
Fixes
| Ticket | Release Notes |
|---|---|
|
IMI-1867 |
Addresses an issue that prevented MeshView from generating a Support Diagnostic Snapshot for a Controller that has been onboarded but not claimed. |
|
IMI-1857 |
Fixes an issue that results in MeshView allowing to un-claim a controller that is not attached |
|
IMI-1818 |
Fixes a problem when the ISP user switches to another premises the URL is not updated properly |
|
IMI-1807 |
Fixes a problem that resulted in the topology in MeshView not being displayed |
|
IMI-1798 |
Fixes an issue that resulted in ISP users being directed to an empty page instead of the Search page when clicking the MeshView tile in Mosaic One |
|
IMI-1789 |
Addresses an issue that resulted in an error when clicking on a MAC for an onboarded Controller that has not been claimed |
|
IMI-1783 |
Fixes a problem that resulted in ISP users being redirected to an empty page when the user attaches a controller and refreshes the Mobile Account view |
|
IMI-1720 |
Fixes a problem with URLs when a Controller is unclaimed |
Errata
| Ticket | Release Notes |
|---|---|
|
IMI-1833 |
MeshView does not show the Offline toast message when a Node or Mobile Account is being watched and it goes offline |
|
IMI-1821 |
MeshView fails to display telemetry data after a node is un-claimed |
|
IMI-1787 |
When the user attaches a controller and refreshes the mobile account view, the message "The controller has no mobile account associated." is displayed. |
|
IMI-1760 |
On occasions, the Uplink stats for a wired backhaul are not displayed in the Node View |
|
IMI-1137 |
The advanced view takes a long time to load when the premises has a large event history. |
|
IMI-1135 |
The newest data point does not match the date on the x-axis for the telemetry charts. |
|
IMI-1120 |
The Topology diagram does not support full screen mode today. |
|
IMI-1118 |
Sometimes backhaul links are drawn over user devices. |
|
IMI-1115 |
When user is on the 24hs or 7days and a new data point arrives, sometimes we're showing a data point that has a future time |
|
IMI-801 |
When unpausing a device, the Topology View still shows the pause icon over devices. |
|
IMI-302 |
Offline/inactive Satellites are not being displayed in the Topology View. |
|
IMI-113 |
For some screen sizes and resolutions, MeshVew cards sometimes end up with horizontal scrolling. |
MeshView Release 9.0.0
Released: October 12, 2023
Features
| Ticket | Release Notes |
|---|---|
|
SDGP-1312 |
ISP users can now attach a Controller to a MAC (pre-provisioning), from the Mobile Account View. |
|
SDGP-1295 |
Intellifi MeshView is now accessible as an Application Tile in the Mosaic One Application launcher. |
|
SDGP-1229 |
Node view now shows the Node a Satellite is connected to |
|
SDGP-1214 |
Display the link quality in the Nodes card in the Premises Overview. |
|
SDGP-1176 |
Provide options to create Virtual Field support tunnels for more than 10 minutes. |
|
SDGP-1175 |
Added the ability to search by Nodes and Mobile Accounts:
|
|
SDGP-1129 |
The MeshView URLs now include the complete path to Nodes or Devices for deep linking. |
|
SDGP-1121 |
The Diagnostics Snapshot in the Advanced View supports download and copy link to tiny URL |
|
SDGP-1120 |
The Mobile Account view now displays the date the account was created. |
|
SDGP-1119 |
ISP users can now start the recovery password process on behalf of the user from the Mobile Account view. |
|
SDGP-1040 |
The Node Inventory is now accessible in the Admin view. |
|
SDGP-982 |
Added Logs to MeshView Admin page. |
|
SDGP-957 |
The Node Inventory can now be downloaded from the Admin view. |
|
SDGP-899 |
MeshView now displays the online status history for Nodes, as a histogram, in the corresponding view |
|
SDGP-897 |
MeshView now exposes the date the Controller was claimed by the subscriber in the Mobile Account view |
|
SDGP-886 |
Added ability to link from Topology to Devices view. |
|
SDGP-885 |
Added ability to link from Topology to Nodes view. |
|
SDGP-846 |
MeshView now defaults to a paginated list of subscribers and nodes for the landing page |
Fixes
| Ticket | Release Notes |
|---|---|
|
IMI-1805 |
Fixes a problem in MeshView when a Controller is loaded and some telemetry charts are missing |
|
IMI-1803 |
Fixes a problem with the 60-second auto refresh in MeshView |
|
IMI-1795 |
Fixes an issue with MeshView when a Controller is using firmware older than 12.1.x resulting in an empty error screen and a never-ending spinner |
|
IMI-1777 |
Fixes a problem in MeshView that results in an infinite spinner when switching from an empty to a non-empty premises |
|
IMI-1769 |
Fixes a problem in MeshView that results in an infinite spinner when the online status history data is not found |
|
IMI-1758 |
Fixes a problem that results in MeshView showing wrong information when the user searches for a Controller with more that one premises |
|
IMI-1704 |
Fixes a problem that results in multiple telemetry gets being executed at the same time, reducing the performance of the interface |
|
IMI-1601 |
Fixes an issue in MeshView that results in the first Virtual Field Tech tunnel not working for a given Controller |
|
IMI-1574 |
Fixes a problem in MeshView that resulted in the user being routed back to the search view when clicking the Intellifi icon in the navigation bar. |
|
IMI-1442 |
Fixes a cosmetic view issue when no value is available for a given parameter in Device View |
|
IMI-1441 |
Prevent MeshView form from showing more than 2 decimal digits for data metrics. |
|
IMI-1434 |
Fixes a problem that allowed the Help Desk user to reset the mobile account password. |
|
IMI-1420 |
Fixes a problem that prevented the user from searching by MAC address and filter via email. |
|
IMI-1419 |
Fixes a problem that prevented full name search from working properly. |
|
IMI-1378 |
Fixes a problem in MeshView search page that results in some filters not working. |
|
IMI-1318 |
Fixes a problem that could result in a 404 error when loading telemetry dat |
|
IMI-1312 |
Fixes a problem that resulted in MeshView displaying an empty page when looking at a Telemetry chart and switching to another premises. |
Errata
| Ticket | Release Notes |
|---|---|
|
IMI-1833 |
MeshView does not show the Offline toast message when a Node is being watched and it goes offline |
|
IMI-1821 |
MeshView fails to display telemetry data after a node is un-claimed |
|
IMI-1787 |
When the user attaches a controller and refreshes the mobile account view, the message "The controller has no mobile account associated." is displayed. |
|
IMI-1760 |
On occasions the Uplink stats for a wired backhaul are not displayed in the Node View |
|
IMI-1137 |
The advanced view takes a long time to load when the premises has a large event history. |
|
IMI-1135 |
The newest data point does not match the date on the x-axis for the telemetry charts. |
|
IMI-1120 |
The Topology diagram does not support full screen mode today. |
|
IMI-1118 |
Sometimes backhaul links are drawn over user devices. |
|
IMI-1115 |
When user is on the 24hs or 7days and a new data point arrives, sometimes we're showing a data point that has a future time |
|
IMI-801 |
When unpausing a device, the Topology View still shows the pause icon over devices. |
|
IMI-302 |
Offline/inactive Satellites are not being displayed in the Topology View. |
|
IMI-113 |
For some screen sizes and resolutions, MeshVew cards sometimes end up with horizontal scrolling. |
