cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 
Highlighted
New Contributor

Could someone please provide a sample configuration for full mesh frame relay (2 T1s) on TA900E?

Jump to solution

I'm involved in project to replace an EoL Cisco 2432 router with an Adtran TA9xxE.  The existing Cisco is using frame relay on the WAN side.  If anyone could give me so pointers on replicating this configuration on the TA9xxE it would be greatly appreciated.

This is the Cisco config in question:

interface Serial1/0:0

description

no ip address

ip load-sharing per-packet

encapsulation frame-relay IETF

load-interval 30

tx-ring-limit 1

tx-queue-limit 1

no arp frame-relay

frame-relay lmi-type ansi

max-reserved-bandwidth 100

service-policy output OUT-POLICY

!

interface Serial1/0:0.30 point-to-point

description Flex

ip address x.x.x.x x.x.x.x

ip load-sharing per-packet

snmp trap link-status

no cdp enable

frame-relay interface-dlci 30 IETF

!

interface Serial1/0:0.31 point-to-point

description Mesh

ip vrf forwarding VPN

ip address x.x.x.x x.x.x.x

ip load-sharing per-packet

ip virtual-reassembly

snmp trap link-status

no cdp enable

frame-relay interface-dlci 31 IETF

!

interface Serial1/1:0

description

no ip address

ip load-sharing per-packet

encapsulation frame-relay IETF

load-interval 30

tx-ring-limit 1

tx-queue-limit 1

no arp frame-relay

frame-relay lmi-type ansi

max-reserved-bandwidth 100

service-policy output OUT-POLICY

!

interface Serial1/1:0.30 point-to-point

description FLEX

ip address x.x.x.x x.x.x.x

ip load-sharing per-packet

snmp trap link-status

no cdp enable

frame-relay interface-dlci 30 IETF

!

interface Serial1/1:0.31 point-to-point

description FLEX

ip vrf forwarding VPN

ip address x.x.x.x x.x.x.x

ip load-sharing per-packet

ip virtual-reassembly

snmp trap link-status

no cdp enable

frame-relay interface-dlci 31 IETF

Thank you!!

Labels (1)
0 Kudos
Reply
1 Solution

Accepted Solutions
New Contributor III

Re: Could someone please provide a sample configuration for full mesh frame relay (2 T1s) on TA900E?

Jump to solution

Here is some syntax help, you to get you started. If both T1's go to the same CO, you may want to set your clock sourcing accordingly to avoid slips.

interface t1 1/1

  description Circuit ID blahblahblah

  tdm-group 1 timeslots 1-24 speed 64

  no shutdown

!

interface t1 1/2

  description Circuit ID blahblahblah

  tdm-group 1 timeslots 1-24 speed 64

  no shutdown

!

interface fr 1 point-to-point

  frame-relay lmi-type ansi

  no shutdown

  cross-connect 1 t1 1/1 1 frame-relay 1

!

interface fr 1.1 point-to-point

  frame-relay interface-dlci 31

  description fr 1.1

  ip address  123.123.123.02  255.255.255.252

set up your other point to points etc

View solution in original post

2 Replies
New Contributor III

Re: Could someone please provide a sample configuration for full mesh frame relay (2 T1s) on TA900E?

Jump to solution

Here is some syntax help, you to get you started. If both T1's go to the same CO, you may want to set your clock sourcing accordingly to avoid slips.

interface t1 1/1

  description Circuit ID blahblahblah

  tdm-group 1 timeslots 1-24 speed 64

  no shutdown

!

interface t1 1/2

  description Circuit ID blahblahblah

  tdm-group 1 timeslots 1-24 speed 64

  no shutdown

!

interface fr 1 point-to-point

  frame-relay lmi-type ansi

  no shutdown

  cross-connect 1 t1 1/1 1 frame-relay 1

!

interface fr 1.1 point-to-point

  frame-relay interface-dlci 31

  description fr 1.1

  ip address  123.123.123.02  255.255.255.252

set up your other point to points etc

View solution in original post

Highlighted
New Contributor

Re: Could someone please provide a sample configuration for full mesh frame relay (2 T1s) on TA900E?

Jump to solution

Thank you very much. That does get me started in the first direction.

0 Kudos
Reply