cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 
meyerj66
New Contributor III

TA900 series CLI

Jump to solution

Is there a list of various show, debug, traceroute, ping, and clear commands via CLI for trouble shooting issues?

Tags (2)
0 Kudos
1 Solution

Accepted Solutions
unified
Valued Contributor
Valued Contributor

Re: TA900 series CLI

Jump to solution

I found this post to be useful:

http://www.markholloway.com/blog/?p=315

Debug Output

COMMANDDESCRIPTION
show debuggingshows current enabled debug commands
debug sip stack messagesshows sip debug information
debug isdn l2-formattedshows isdn debug information (easier use)
debug voice verboseshows all voice messaging
debug isdn verboseshows all isdn messaging
debug interface T1 0/4 rbsshows robbed bit signaling from CAS circuit
undebug allturns off all debugging

Utility Commands

COMMANDDESCRIPTION
clear count mediacounters on media-gateway reset
clear countersclears counters on interfaces
no eventsturns off messages to the current session
pingping an IP address
traceroutetrace the router path to a destination IP address
wallsends a broadcast message to all current users
sip trunk-registration force-registerforces sip re-registration

Show Commands

COMMANDDESCRIPTION
show sip trunk-registrationshows registration status
show media-gateway summaryshows media gateway channel status
show media-gateway channel 0/2.1shows media gateway channel details
show qos mapshows qos map
show flashlists contents of the flash
show run voice [verbose]lists running configuration for voice provisioning
show hostsshows the hosts table with timers
show event-historyshows events and terminal commands typed
show interfacesshows interface details
show systemshows uptime, firmware version and timing
show thresholdsshows thresholds of T1 interfaces
show usersshows current users
show voice quality-statsshows call information including lost packets
show voice quality-stats activeshows call information including lost
show voice quality-stats active realtimeshows call information including lost
show ip trafficTCP and UDP statistics

View solution in original post

0 Kudos
2 Replies
unified
Valued Contributor
Valued Contributor

Re: TA900 series CLI

Jump to solution

I found this post to be useful:

http://www.markholloway.com/blog/?p=315

Debug Output

COMMANDDESCRIPTION
show debuggingshows current enabled debug commands
debug sip stack messagesshows sip debug information
debug isdn l2-formattedshows isdn debug information (easier use)
debug voice verboseshows all voice messaging
debug isdn verboseshows all isdn messaging
debug interface T1 0/4 rbsshows robbed bit signaling from CAS circuit
undebug allturns off all debugging

Utility Commands

COMMANDDESCRIPTION
clear count mediacounters on media-gateway reset
clear countersclears counters on interfaces
no eventsturns off messages to the current session
pingping an IP address
traceroutetrace the router path to a destination IP address
wallsends a broadcast message to all current users
sip trunk-registration force-registerforces sip re-registration

Show Commands

COMMANDDESCRIPTION
show sip trunk-registrationshows registration status
show media-gateway summaryshows media gateway channel status
show media-gateway channel 0/2.1shows media gateway channel details
show qos mapshows qos map
show flashlists contents of the flash
show run voice [verbose]lists running configuration for voice provisioning
show hostsshows the hosts table with timers
show event-historyshows events and terminal commands typed
show interfacesshows interface details
show systemshows uptime, firmware version and timing
show thresholdsshows thresholds of T1 interfaces
show usersshows current users
show voice quality-statsshows call information including lost packets
show voice quality-stats activeshows call information including lost
show voice quality-stats active realtimeshows call information including lost
show ip trafficTCP and UDP statistics

View solution in original post

0 Kudos
david
Valued Contributor
Valued Contributor

Re: TA900 series CLI

Jump to solution

meyerj66,

I went ahead and flagged this post as "Assumed Answered".  If the response on this thread assisted you, please mark it as Correct or Helpful as the case may be with the applicable buttons.  This will make it visible and help other members of the community find solutions more easily.  If you still need assistance, I would be more than happy to continue working with you on this - just let me know in a reply.

Thanks!

David