What is the basic setup procedure? I want each FXS to have its own number. I also want that number to be the outgoing caller ID for each port. My PRI will use B8ZS, NI-2 abd ESF. I am looking through the manual but I need to get this ready very soon.
Does this look like it will route calls from the PRI to the unique ten digit In#Accept number I added to each FXS port? I am receiving ten digits from the PRI and want to send the DID number back out as outgoing caller id.
Network Termx # Slot/Svc Port/PEP Sig Out#Accept Out#Rej Ifce Config
Network Term x 1 N1)T1/PRI-1 1)T1/PRI PRI [$] [--] [+]
National ISDN
First DS0 1
x Number of DS0s 23
x Outgoing Number Conv. ISDN-National As Dialed
x Strip MSD None
x Ntwrk Spec. Fac. - Voice Normal
x Ntwrk Spec. Fac. - Data Normal
x Called Digits Transfered All
x Outgoing Caller ID Send as provided
x Source ID 0
x Swap ANI/DNIS Disabled
x B Channel Selection Normal
x Busy Option Normal
x
Network Termx # Slot/Svc Port/PEP Sig In#Accept Out#Rej Ifce Config
User Term x 1 S1)FXS-8 1)FXS 1/1 [715xxxxxxx] [+] [Port=1]
Global Paramx 2 S1)FXS-8 2)FXS 1/2 [715xxxxxxx] [+] [Port=2]
x 3 S1)FXS-8 3)FXS 1/3 [715xxxxxxx] [+] [Port=3]
x 4 S1)FXS-8 4)FXS 1/4 [715xxxxxxx] [+] [Port=4]
x 5 S1)FXS-8 5)FXS 1/5 [715xxxxxxx] [+] [Port=5]
x 6 S1)FXS-8 6)FXS 1/6 [715xxxxxxx] [+] [Port=6]
x 7 S1)FXS-8 7)FXS 1/7 [715xxxxxxx] [+] [Port=7]
x 8 S1)FXS-8 8)FXS 1/8 [715xxxxxxx] [+] [Port=8]
Incoming Number Accept Listx # Src ID Accept Number Search Data 64K Data 56
Incoming Number Accept Listx 1 0 715xxxxxxx Primary Enabled Enable
Incoming Number Accept Listx Ports Available !sssssss
x Number of Ports 1
x Signaling Method Loop Start
x Forward Disconnect 600 mS
x Direct Inward Dialing Enabled
x Caller ID number 715xxxxxxx
x DID Digits Transferred 10
x Strip MSD None
x Source ID 0
x Port Selection Normal
x Dial on Offhook --
x ANI to Caller ID Enabled
Message was edited by: Josh Kretzschmar
I was just writing up an answer, but it looks like you figured it all out.
Under the USER TERM, under the IFCE CONFIG for the FXS ports, the "Caller ID number" is the outbound caller ID transmitted on an call originated from that FXS port.
You configuration looks spot-on! Good job!
Obviously you'll need to add the Slot 2 and Slot 3 ports, but I believe you have it.
One thing to know, is that if the inbound number is 10 digits, under the DIAL PLAN and GLOBAL PARAM, make sure there is no AREA or CITY CODE configured in there (otherwise it will route based on the number minus the area code).
Also, under NUMBER COMPLETE TEMPLATES, the ATLAS defaults to 7-digit local dialing, so if you are in a 10-digit dialing area you'll need to change the first entry from "NXX-XXXX" to "NXX-NXX-XXXX".
Take care,
Patrick
I was just writing up an answer, but it looks like you figured it all out.
Under the USER TERM, under the IFCE CONFIG for the FXS ports, the "Caller ID number" is the outbound caller ID transmitted on an call originated from that FXS port.
You configuration looks spot-on! Good job!
Obviously you'll need to add the Slot 2 and Slot 3 ports, but I believe you have it.
One thing to know, is that if the inbound number is 10 digits, under the DIAL PLAN and GLOBAL PARAM, make sure there is no AREA or CITY CODE configured in there (otherwise it will route based on the number minus the area code).
Also, under NUMBER COMPLETE TEMPLATES, the ATLAS defaults to 7-digit local dialing, so if you are in a 10-digit dialing area you'll need to change the first entry from "NXX-XXXX" to "NXX-NXX-XXXX".
Take care,
Patrick
Thank you very much for the response Patrick. I do have slots two and three configured the same. I removed the area code and changed the local dialing entry. Now I just have to wait for my PRI and test it out.