cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 
Anonymous
Not applicable

I have 3 adtran netvanta 1550 wsitches.

Jump to solution

I am trying to setup a vlan in them but I cannot seem to get tot the management console.

I can boot them and get in with the console cable. all 3 say they are at 10.10.10.1 ip address.

So I decided that I would turn everything off and isolate the switches and try to connect with http.

no luck.

so now I am trying to change their ip address via the console.

Can you tell me the commands to change them.

I need to put them in my network anyway and this would get me there I hope.

I have rebooted them several times, left them off for 30 minutes and still nothing.

I cannot telnet, ping or manage with http. just the console cable.

Thanks for any help.

0 Kudos
1 Solution

Accepted Solutions
Anonymous
Not applicable

Re: I have 3 adtran netvanta 1550 wsitches.

Jump to solution

This switch is shipping with an unsupported BVS1.0 firmware that will be changed, and it does not operate as the Guide says.  This is the reason a corrected guide is not provided.

ADTRAN apologizes for this current issue.

To access the device with firmware versions earlier then the supported R13.2.2 ( or current EMR release), you have two options.

Option 1.  The console port will allow you access to the switch with a serial Cisco cable to the unit.

From the console interface you can set the IP address of the switch, to allow you web access later.  Defaults -

Username:  admin

Password:   password

Example:

1550-24>

1550-24>en

1550-24#con t

1550-24(config)#int vlan 1

1550-24(config-intf-vlan 1)#ip address 10.19.221.50 /24 <------- Whatever IP address you like

1550-24(config-intf-vlan 1)#no shut

1550-24(config-intf-vlan 1)#exit

1550-24(config)#exit

Appropriate commands must be issued to preserve configuration.

1550-24#wr

Building configuration...

  1. Success!

1550-24#

Now using a PC connected to an Ethernet port ( with IP address 10 .19.221.51 ) you should be able to access the switch web interface. http://10.19.221.50

Option 2. If you connect the switch to a network with a DHCP server, you should be able to hit the Web interface at the 10.10.10.1 ( or the DHCP assigned IP address) as the Quick Start Guide documents.  The IP address assigned, will bring up the VLAN interface and then the secondary IP 10.10.10.1 will also be responsive. 

As far as all Adtran switches, it is recommended to upgrade them to the current EMR release ( R13.2.2 ).  This is especially true of the 1550 series switches since they can become completely un-responsive with BVS1.0 firmware.

The firmware is available on our website www.ADTRAN.com under Home»Support»Product Downloads»Software Releases

The upgrade instructions are also linked in the Release Notes of the Firmware release.  It will point to https://supportforums.adtran.com/docs/DOC-1672 for Upgrading Firmware in AOS.

The web interface firmware upgrade is usually the easiest method.

View solution in original post

2 Replies
Anonymous
Not applicable

Re: I have 3 adtran netvanta 1550 wsitches.

Jump to solution

This switch is shipping with an unsupported BVS1.0 firmware that will be changed, and it does not operate as the Guide says.  This is the reason a corrected guide is not provided.

ADTRAN apologizes for this current issue.

To access the device with firmware versions earlier then the supported R13.2.2 ( or current EMR release), you have two options.

Option 1.  The console port will allow you access to the switch with a serial Cisco cable to the unit.

From the console interface you can set the IP address of the switch, to allow you web access later.  Defaults -

Username:  admin

Password:   password

Example:

1550-24>

1550-24>en

1550-24#con t

1550-24(config)#int vlan 1

1550-24(config-intf-vlan 1)#ip address 10.19.221.50 /24 <------- Whatever IP address you like

1550-24(config-intf-vlan 1)#no shut

1550-24(config-intf-vlan 1)#exit

1550-24(config)#exit

Appropriate commands must be issued to preserve configuration.

1550-24#wr

Building configuration...

  1. Success!

1550-24#

Now using a PC connected to an Ethernet port ( with IP address 10 .19.221.51 ) you should be able to access the switch web interface. http://10.19.221.50

Option 2. If you connect the switch to a network with a DHCP server, you should be able to hit the Web interface at the 10.10.10.1 ( or the DHCP assigned IP address) as the Quick Start Guide documents.  The IP address assigned, will bring up the VLAN interface and then the secondary IP 10.10.10.1 will also be responsive. 

As far as all Adtran switches, it is recommended to upgrade them to the current EMR release ( R13.2.2 ).  This is especially true of the 1550 series switches since they can become completely un-responsive with BVS1.0 firmware.

The firmware is available on our website www.ADTRAN.com under Home»Support»Product Downloads»Software Releases

The upgrade instructions are also linked in the Release Notes of the Firmware release.  It will point to https://supportforums.adtran.com/docs/DOC-1672 for Upgrading Firmware in AOS.

The web interface firmware upgrade is usually the easiest method.

Anonymous
Not applicable

Re: I have 3 adtran netvanta 1550 wsitches.

Jump to solution

Thank you very much. worked like a charm.

Firmware is updated.

You are the best.