Adtran
Help
The Adtran community holiday season is starting next week! The holiday period will span from December 21, 2024 to January 6, 2025. During this time, responses to feedback form submissions may be delayed. If you are encountering product issues, you can reach out to Adtran support at any time.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Show  only  | Search instead for 
Did you mean: 
davide
New Contributor
‎05-25-2016 03:49 PM

Netvanta 1550-48 PoE stuck in a loop. After a power failure my Netvanta 1550-48 PoE started looping and getting irresponsive with the "m_socket Fd(-1) is not a valid descriptor. connect: Connection refused" message. All I could do was to use bootstrap an

After a power failure my Netvanta 1550-48 PoE started looping and getting irresponsive with  the "m_socket Fd(-1) is not a valid descriptor. connect: Connection refused" message. All I could do was to use bootstrap and bypass the startup config file. Then I just copied and pasted the old startup configuration file.  I saved and it was working fine.

Here is the flash:

MZ-SW-2#sh flash

       20456520 97101524-2RBVS10.biz

          12766 config-MZ-SW-2-04-12-2016.cfg

         908035 exception-report-20160522213604.tgz

         808052 exception-report-20160522231939.tgz

         808269 exception-report-20160522232153.tgz

         807824 exception-report-20160522232324.tgz

         807650 exception-report-20160522232455.tgz

         808052 exception-report-20160522233626.tgz

         808352 exception-report-20160522233829.tgz

         808228 exception-report-20160522233830.tgz

         807953 exception-report-20160522234003.tgz

         808530 exception-report-20160522234004.tgz

         807016 exception-report-20160522235412.tgz

       20660104 NV1550A-R11-10-2.biz

          12524 startup-config

          12525 startup-config.bak

51105792 bytes used*, 37675008 available**, 88780800 total

I was wondering if I may deleted the *.tgz files and mostly what is going to happen if I restart the switch.

0 Kudos
Reply
2 Replies
Anonymous
Not applicable
‎05-26-2016 02:03 PM

Re: Netvanta 1550-48 PoE stuck in a loop. After a power failure my Netvanta 1550-48 PoE started looping and getting irresponsive with the "m_socket Fd(-1) is not a valid descriptor. connect: Connection refused" message. All I could do was to use bootstra

Davide

Since this post is for a NetVanta 1550 and not a TA 1500, we are going to move it to that area of the Support Community to improve the chances of getting some help from the community.  Also, based on the description of the issue, it may be best to open a support case with ADTRAN.  A ticket can be opened on the web (adtran.com/supportcase) or via telephone (888-423-8726).”


Thanks,

Charles

0 Kudos
Accept as Solution Reply
Anonymous
Not applicable
‎01-13-2017 03:28 PM

Re: Netvanta 1550-48 PoE stuck in a loop. After a power failure my Netvanta 1550-48 PoE started looping and getting irresponsive with the "m_socket Fd(-1) is not a valid descriptor. connect: Connection refused" message. All I could do was to use bootstra

Please be sure to upgrade to the latest supported firmware at all installs - R11.10.6 currently resolves many of the 1550 issues reported and found later.

0 Kudos
Accept as Solution Reply