cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 
shane
New Contributor

Basic configuration question

Jump to solution

I have just set up a 3430 with a T1 circuit. What I am trying to accomplish is just a simple setup that would be like if I were just setting up a small in home router with cable or DSL. I am trying to figure out how to just use DHCP with a private default gateway such as 10.0.0.1 or 192.168.1.1. The router would be connected to a 24 port switch and the clients would just pull DHCP. Can anyone help this newbie accomplish this?

Labels (1)
0 Kudos
1 Solution

Accepted Solutions
Anonymous
Not applicable

Re: Basic configuration question

Jump to solution

:

Thank you for asking this question on the support community.  It sounds like you are only missing a few steps.  If you have the T1 configured and routing setup already (as it appears you do), then you will need to configure the LAN IP address, firewall (for NAT) and DHCP.  All of these steps are covered below.

The Configuring Internet Access (Many to One NAT) with the Firewall Wizard video walks you through how to setup the firewall for NAT and Internet access.  Furthermore, the Configuring T1 and E1 Internet Access in AOS has detailed information on setting up the T1, firewall, and IP addressing in written form. 

Here is a post on how to setup DHCP (it also links the DHCP guide): 

Finally, this post has information on setting up a T1 and assigning public IP addresses for Internet access (for reference): 

I hope that makes sense, but please do not hesitate to reply to this post with any additional questions.  I will be happy to help in any way I can.

Levi

View solution in original post

0 Kudos
3 Replies
shane
New Contributor

Re: Basic configuration question

Jump to solution

To elaborate a little further. I have the HDLC configured and have internet access to my test pc when plugged directly into the Eth 0/1 port. I had to statically configure the computer with one of the public IPs off of the LAN IP Block. The default gateway on the Eth 0/1 interface is also set to the first usable IP on the LAN block provided by the ISP. I am trying to figure out how to change the default gateway to a generic 192.168.x.x and use DHCP down to any clients that will be behind the switch.

Anonymous
Not applicable

Re: Basic configuration question

Jump to solution

:

Thank you for asking this question on the support community.  It sounds like you are only missing a few steps.  If you have the T1 configured and routing setup already (as it appears you do), then you will need to configure the LAN IP address, firewall (for NAT) and DHCP.  All of these steps are covered below.

The Configuring Internet Access (Many to One NAT) with the Firewall Wizard video walks you through how to setup the firewall for NAT and Internet access.  Furthermore, the Configuring T1 and E1 Internet Access in AOS has detailed information on setting up the T1, firewall, and IP addressing in written form. 

Here is a post on how to setup DHCP (it also links the DHCP guide): 

Finally, this post has information on setting up a T1 and assigning public IP addresses for Internet access (for reference): 

I hope that makes sense, but please do not hesitate to reply to this post with any additional questions.  I will be happy to help in any way I can.

Levi

View solution in original post

0 Kudos
Anonymous
Not applicable

Re: Basic configuration question

Jump to solution

@shane:

I went ahead and flagged the "Correct Answer" on this post to make it more visible and help other members of the community find solutions more easily. If you don't feel like the answer I marked was correct, feel free to come back to this post and unmark it and select another in its place with the applicable buttons.  If you still need assistance, we would be more than happy to continue working with you on this - just let us know in a reply.

Thanks,

Levi