cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 
Highlighted
Contributor
Contributor

Show Probe in list tracked by "Nothing"?

Jump to solution

I'm wondering if this is normal and if so, why it is...

My partial config:

probe ComcastProbe-1 icmp-echo

  destination 8.8.8.8

  source-address  x.x.x.x

  period 5

  tolerance consecutive fail 5 pass 3

  no shutdown

!

probe ComcastProbe-2 icmp-echo

  destination 8.8.4.4

  source-address  x.x.x.x

  period 5

  tolerance consecutive fail 5 pass 3

  no shutdown

!

probe ComcastProbe-3 icmp-echo

  destination 4.2.2.1

  source-address x.x.x.x

  period 5

  tolerance consecutive fail 5 pass 3

  no shutdown

!

track "WAN_TEST"

  log-changes

  snmp trap state-change

  test list or

    if probe ComcastProbe-1

    if probe ComcastProbe-2

    if probe ComcastProbe-3

  no shutdown

!

...end

Why does the Comcast-3 probe indicate that it is tracked by "Nothing"?   Is this normal?

FP3448(config)#do sh probe

Probe ComcastProbe-1:

  Current State: PASS  Admin. Status: UP

  Type: ICMP Echo  Period: 5 sec  Timeout: 1500 msec

  Source: x.x.x.x  Destination: 8.8.8.8

  Data size: 0

Tracked by: WAN_TEST

  Tests Run: 46872  Failed: 2

  Tolerance: 0 consecutive failures currently, 5 needed to FAIL

  Time in current state: 2 days, 17 hours, 25 minutes, 34 seconds

Probe ComcastProbe-2:

  Current State: PASS  Admin. Status: UP

  Type: ICMP Echo  Period: 5 sec  Timeout: 1500 msec

  Source: x.x.x.x  Destination: 8.8.4.4

  Data size: 0

Tracked by: WAN_TEST

  Tests Run: 46872  Failed: 5

  Tolerance: 0 consecutive failures currently, 5 needed to FAIL

  Time in current state: 2 days, 17 hours, 25 minutes, 33 seconds

Probe ComcastProbe-3:

  Current State: PASS  Admin. Status: UP

  Type: ICMP Echo  Period: 5 sec  Timeout: 1500 msec

  Source: x.x.x.x  Destination: 4.2.2.1

  Data size: 0

Tracked by: Nothing

  Tests Run: 46873  Failed: 1

  Tolerance: 0 consecutive failures currently, 5 needed to FAIL

  Time in current state: 2 days, 17 hours, 25 minutes, 32 seconds

Thanks,

Dan

Labels (3)
0 Kudos
1 Solution

Accepted Solutions
Highlighted
Anonymous
Not applicable

Re: Show Probe in list tracked by "Nothing"?

Jump to solution

:

This appears to be a display issue with the show probe command when there are more than two entries in the "test list" probe configuration.  It should not affect functionality at all. Thank you for bringing this to our attention.  Let me know if you have any additional questions.

Levi

View solution in original post

0 Kudos
4 Replies
Highlighted
Anonymous
Not applicable

Re: Show Probe in list tracked by "Nothing"?

Jump to solution

:

Thank you for asking this question in the support community.  What firmware version is running on this device?  Also, what does the output of the show track command produce?  Do all the probes show they are tracked?

Levi

Highlighted
Contributor
Contributor

Re: Show Probe in list tracked by "Nothing"?

Jump to solution

Levi,

The 3448 is running 18.03.01.00.E

FP3448#sh track

Track WAN_TEST:

  Current State: PASS     (Admin: UP)

  Testing:

    probe ComcastProbe-1 (PASS)

    OR probe ComcastProbe-2 (PASS)

    OR probe ComcastProbe-3 (PASS)

  Dampening Interval: 1 seconds

  Time in current state: 4 days, 20 hours, 53 minutes, 44 seconds

  Track State Changes: 0

  Tracking:

    ip route 0.0.0.0 0.0.0.0 X.X.160.54

FP3448#

Shows all three!

Dan

Highlighted
Anonymous
Not applicable

Re: Show Probe in list tracked by "Nothing"?

Jump to solution

:

This appears to be a display issue with the show probe command when there are more than two entries in the "test list" probe configuration.  It should not affect functionality at all. Thank you for bringing this to our attention.  Let me know if you have any additional questions.

Levi

View solution in original post

0 Kudos
Highlighted
Contributor
Contributor

Re: Show Probe in list tracked by "Nothing"?

Jump to solution

I had the opportunity to check 3 other sites which are also running probe lists and they also had the display issue.  They all seem to be functioning correctly. 

Dan