Channel wise Caller ID

[Anonymous]

Is there a way to assign channel wise caller id?

[Anonymous]

Hello,

Thank you for posting to our Support Forum.  In order to properly answer your question, I would like to ask you a few questions about your application.

1.  Are you using T1 PRI, RBS Wink/Immediate, IP Phones, or Analog FXS Phones on the customer side?

2.  Would you mind posting your voice configuration (show run voice)?  You can omit any IP address or sensitive information in the config.

Thanks,

Geoff

ADTRAN Technical Support

[Anonymous]

I agree I should have supplied more information.... here it is...

1. I am using T1 RBS Wink between TA908e and my Dialer

2. here is the sh run output on my TA908e

LES_TA908e#sh run voice

Building configuration...

!

!

voice feature-mode network

voice forward-mode network

!

!

!

!

!

!

!

voice dial-plan 1 local NXX-NXX-XXXX

!

!

!

!

voice codec-list "ALL Codecs"

  codec g711ulaw

  codec g729

!

voice codec-list 729

  default

  codec g729

!

!

voice trunk-list SIP

  trunk T05

!

!

voice trunk T03 type t1-rbs supervision wink role network

  description "RBS to PBX"

  resource-selection linear ascending

  caller-id-override number-inbound **********

  did digits-transferred 4

  connect t1 0/3 tdm-group 1

  rtp delay-mode adaptive

  rtp qos dscp 0

  codec-group 729

!

voice trunk T04 type t1-rbs supervision wink role network

  description "RBS to PBX"

  resource-selection linear ascending

  caller-id-override number-inbound **********

  did digits-transferred 4

  connect t1 0/4 tdm-group 1

  rtp delay-mode adaptive

  codec-group 729

!

voice trunk T05 type sip

  description "SIP_PXXXX"

  sip-server primary ************

  codec-group 729

!

!

voice grouped-trunk SIP

  trunk T05

  accept $ cost 0

!

!

voice grouped-trunk "RBS T1 TO PBX"

  trunk T04

  trunk T03

  accept $ cost 0

  accept 1-855-NXX-NXXX cost 0

  accept 1-855-NXX-XXXX cost 0

  accept 1-800-NXX-NXXX cost 0

  permit list SIP

  !deny all other trunks

  !deny all other ani

!      

!      

!      

!      

!      

!      

!      

!      

!      

end    

[Anonymous · Accepted solution]

Hello,

No problem.  If you want to have specific caller id for each DS0 or T1 timeslot, you will need to make some configuration changes.  You will need 24 individual timeslots in the T1 interface:

interface t1 0/4

  tdm-group 1 timeslots 1 speed 64

  tdm-group 2 timeslots 2 speed 64

  tdm-group 3 timeslots 3 speed 64

  tdm-group 4 timeslots 4 speed 64

  tdm-group 5 timeslots 5 speed 64

  tdm-group 6 timeslots 6 speed 64

  tdm-group 7 timeslots 7 speed 64

  tdm-group 8 timeslots 8 speed 64

  tdm-group 9 timeslots 9 speed 64

  tdm-group 10 timeslots 10 speed 64

  tdm-group 11 timeslots 11 speed 64

  tdm-group 12 timeslots 12 speed 64

  tdm-group 13 timeslots 13 speed 64

  tdm-group 14 timeslots 14 speed 64

  tdm-group 15 timeslots 15 speed 64

  tdm-group 16 timeslots 16 speed 64

  tdm-group 17 timeslots 17 speed 64

  tdm-group 18 timeslots 18 speed 64

  tdm-group 19 timeslots 19 speed 64

  tdm-group 20 timeslots 20 speed 64

  tdm-group 21 timeslots 21 speed 64

  tdm-group 22 timeslots 22 speed 64

  tdm-group 23 timeslots 23 speed 64

  tdm-group 24 timeslots 24 speed 64

  no shutdown

!

Then you will need a unique Wink T1 voice trunk for each TDM group.  It will need to be setup this way in order to put a unique caller id per DS0:

!

voice trunk T11 type t1-rbs supervision wink role network

  connect t1 0/4 tdm-group 1

  caller-id-override number-inbound 555-222-1101

  rtp delay-mode adaptive

!

voice trunk T12 type t1-rbs supervision wink role network

  connect t1 0/4 tdm-group 2

  caller-id-override number-inbound 555-222-1102

  rtp delay-mode adaptive

!

voice trunk T13 type t1-rbs supervision wink role network

  connect t1 0/4 tdm-group 3

  caller-id-override number-inbound 555-222-1103

  rtp delay-mode adaptive

!

voice trunk T14 type t1-rbs supervision wink role network

  connect t1 0/4 tdm-group 4

  caller-id-override number-inbound 555-222-1104

  rtp delay-mode adaptive

!

voice trunk T15 type t1-rbs supervision wink role network

  connect t1 0/4 tdm-group 5

  caller-id-override number-inbound 555-222-1105

  rtp delay-mode adaptive

!

voice trunk T16 type t1-rbs supervision wink role network

  connect t1 0/4 tdm-group 6

  caller-id-override number-inbound 555-222-1106

  rtp delay-mode adaptive

!

voice trunk T17 type t1-rbs supervision wink role network

  connect t1 0/4 tdm-group 7

  caller-id-override number-inbound 555-222-1107

  rtp delay-mode adaptive

!

voice trunk T18 type t1-rbs supervision wink role network

  connect t1 0/4 tdm-group 8

  caller-id-override number-inbound 555-222-1108

  rtp delay-mode adaptive

!

voice trunk T19 type t1-rbs supervision wink role network

  connect t1 0/4 tdm-group 9

  caller-id-override number-inbound 555-222-1109

  rtp delay-mode adaptive

!

voice trunk T20 type t1-rbs supervision wink role network

  connect t1 0/4 tdm-group 10

  caller-id-override number-inbound 555-222-1110

  rtp delay-mode adaptive

!

voice trunk T21 type t1-rbs supervision wink role network

  connect t1 0/4 tdm-group 11

  caller-id-override number-inbound 555-222-1111

  rtp delay-mode adaptive

!

voice trunk T22 type t1-rbs supervision wink role network

  connect t1 0/4 tdm-group 12

  caller-id-override number-inbound 555-222-1112

  rtp delay-mode adaptive

!

voice trunk T23 type t1-rbs supervision wink role network

  connect t1 0/4 tdm-group 13

  caller-id-override number-inbound 555-222-1113

  rtp delay-mode adaptive

!

voice trunk T24 type t1-rbs supervision wink role network

  connect t1 0/4 tdm-group 14

  caller-id-override number-inbound 555-222-1114

  rtp delay-mode adaptive

!

voice trunk T25 type t1-rbs supervision wink role network

  connect t1 0/4 tdm-group 15

  caller-id-override number-inbound 555-222-1115

  rtp delay-mode adaptive

!

voice trunk T26 type t1-rbs supervision wink role network

  connect t1 0/4 tdm-group 16

  caller-id-override number-inbound 555-222-1116

  rtp delay-mode adaptive

!

voice trunk T27 type t1-rbs supervision wink role network

  connect t1 0/4 tdm-group 17

  caller-id-override number-inbound 555-222-1117

  rtp delay-mode adaptive

!

voice trunk T28 type t1-rbs supervision wink role network

  connect t1 0/4 tdm-group 18

  caller-id-override number-inbound 555-222-1118

  rtp delay-mode adaptive

!

voice trunk T29 type t1-rbs supervision wink role network

  connect t1 0/4 tdm-group 19

  caller-id-override number-inbound 555-222-1119

  rtp delay-mode adaptive

!

voice trunk T30 type t1-rbs supervision wink role network

  connect t1 0/4 tdm-group 20

  caller-id-override number-inbound 555-222-1120

  rtp delay-mode adaptive

!

voice trunk T31 type t1-rbs supervision wink role network

  connect t1 0/4 tdm-group 21

  caller-id-override number-inbound 555-222-1121

  rtp delay-mode adaptive

!

voice trunk T32 type t1-rbs supervision wink role network

  connect t1 0/4 tdm-group 22

  caller-id-override number-inbound 555-222-1122

  rtp delay-mode adaptive

!

voice trunk T33 type t1-rbs supervision wink role network

  connect t1 0/4 tdm-group 23

  caller-id-override number-inbound 555-222-1123

  rtp delay-mode adaptive

!

voice trunk T34 type t1-rbs supervision wink role network

  connect t1 0/4 tdm-group 24

  caller-id-override number-inbound 555-222-1124

  rtp delay-mode adaptive

As you can see each DS0 will have its own caller id when the call is initiated from the Dialer and it goes out to the SIP network.  Let me know if you have any questions.

Regards,

Geoff

ADTRAN Technical Support

[Anonymous]

This is great. Thanks Geo. I would like to test this out but before I do I need to know this... I have a full control over all the channels on each trunk on my dialer. Meaning I can group these channels and assign them to different campaigns. What I want to know is... is there any provision that I can make on TA908e so that the call flows on the same channels(from and to) like say calls from Channel 1 thru 10 on T 0/1 on dialer should flow to timeslot 1 thru 10 on t 1/0 on TA908e. These calls intended for a campaign should flow on the same channel and avoid mixing the caller id from another channels.

Please let me know if you need more information.

Thanks,

Deepak

[Anonymous]

Deepak,

If you want to keep proper call flow and caller id on the respective channel, you will need to make a grouped-trunk for each voice trunk:

voice grouped-trunk WINK1

  trunk T11

  accept 555-1001 cost 0

!

voice grouped-trunk WINK2

  trunk T12

  accept 555-1002 cost 0

!

voice grouped-trunk WINK3

  trunk T13

  accept 555-1003 cost 0

!

voice grouped-trunk WINK4

  trunk T14

  accept 555-1004 cost 0

As you can see above, each grouped-trunk has a specific 7 digit accept, so if 555-1003 come in from the sip side, the ADTRAN will route that number to T13, which is tdm-group 3 (DS0/Timeslot 3) on the T1 connected to the dialer.  Note that your accepts could be 4 or 10 digits.  I just used 7 in this example.

Your dialer will be responsible for the timeslot selected when making an outbound call.  So if  555-222-1121 needs to make a call from the Dialer, the Dialer will need to use DS0 21.  When the outbound call is switched to the SIP side, 555-222-1121 will be used for the caller id.

Regards,

Geoff

ADTRAN Technical Support

[Anonymous]

Is there a way or command for me to check real time calls per ds0 or timeslots? I want to make sure that if I send a call on 21st channel from my dialer it should also land on 26th channel of the ta908e.

[Anonymous]

Hello Deepak,

It should not be too hard to verify this if you only have one active call.  You can do:

show int t1 0/4 realtime

Look at the Tx and Rx (A&B) signaling bits.  You should see 11 11 for an active call in E&M mode.  All other DS0s should be 00 00 (idle).

Regards,

Geoff

ADTRAN Technical Support

[Anonymous]

Geo - First of all, Thank you very much. It really helped and it is working as I expected. The only question I have is- I did not create the grouped trunk as you suggested above and it is still working. Is the grouped trunking for inbound calls? I am only concerned with outbound calls and I think I am ok if I don't group the trunk. Please advise.

-Deepak

[Anonymous]

No problem Deepak.  We appreciate you contributing to our Community Forum.  You are correct thinking that the voice grouped-trunk (Trunk Group in the GUI) would allow you to receive inbound SIP to RBS calls.  When a grouped-trunk is created and associated to a voice trunk (Trunk Account in the GUI), the accept numbers in the grouped-trunk allow a call to be routed/switched to that respective trunk.  You need the grouped-trunk for SIP so you can make outbound RBS to SIP calls, but as you stated, you can omit the RBS grouped-trunk if you will not be receiving any inbound (SIP to RBS) calls.

Regards,

Geoff

Technical Support Engineer

[Anonymous]

Thanks again.

-Deepak