cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 
Highlighted
New Contributor III

Do you have a list of what IP PBX's and Feature Servers you have done SIP trunking interoperability testing with and validated interoperability.

0 Kudos
1 Solution

Accepted Solutions
Highlighted
Contributor
Contributor

You can find a list of tested & supported softswitches/feature servers in the , but here's is a listing:  And yes, we use "SIP" Username "Identities" & Password Authentication.

Supported SIP Feature Servers
Altigen
Asterisk
Broadsoft
Metaswitch
Nortel CS2000
Nortel MCS 5200
Shoretel
Sonus ASX
Sylantro

View solution in original post

0 Kudos
9 Replies
Highlighted
Anonymous
Not applicable

There is no list that I’m aware of but then the 7000 series is a PBX/Feature Server on its own, so it wouldn’t really be tested with other PBX’s and feature servers. We do however have a list of SIP trunking providers that we work with ...


https://www.adtran.com/web/page/portal/Adtran/wp_partners_siptrunking

Ronnie

Highlighted
Anonymous
Not applicable

Could you perhaps be looking for information on a gateway device rather than our PBX product? Say for example TA900 or the NetVanta 6000 series?

Highlighted
New Contributor III

Yes. That is exactly what I am looking for. The TA900 series and the

NetVanta 644. I have customers that like to do SIP Trunks and break that

out to a IP PBX, PRI, or POTS config. Also does the TA900 series and

NetVanta 644 prefer SIP Username and Password or IP based authentication?

Thanks,

Joe

On Fri, Apr 6, 2012 at 11:02 AM, racolvin <

Highlighted
Contributor
Contributor

You can find a list of tested & supported softswitches/feature servers in the , but here's is a listing:  And yes, we use "SIP" Username "Identities" & Password Authentication.

Supported SIP Feature Servers
Altigen
Asterisk
Broadsoft
Metaswitch
Nortel CS2000
Nortel MCS 5200
Shoretel
Sonus ASX
Sylantro

View solution in original post

0 Kudos
Highlighted
Anonymous
Not applicable

I relocated this post to the area.

Thanks,
Matt

Highlighted
New Contributor III

Thank you for your response. I tried to use SIP Username & Password and I

was getting a "403 response" when I changed it to IP based I was able to

make outbound calls. I am using Asterisk servers. Any thoughts?

On Mon, Apr 9, 2012 at 10:02 AM, burgermeister <

Highlighted
Valued Contributor
Valued Contributor

Meyerj66,

Below are configuration examples for how I typically setup username and passwords for voice users and trunks.  Of course, you will need to swap phone numbers, auth-name, etc with your specific DIDs.

! SIP voice user (FXS)

voice user 1000

  connect fxs 0/1

  sip-identity 1000 T01 register auth-name "1000" password "1234"

! SIP trunk registration on behalf of a PRI or CAS trunk.

voice trunk T01 type sip

   register 1000 auth-name "1000" password "1234"

At this point, we would likely need to see a "debug sip stack messages" to verify which device is sending the 403 message.  If the Asterisk is sending the 403, you will likely need to check its log to determine why that message is sent.  If the Adtran unit is sending the 403, typically the following debug output will allow us to determine the cause.

debug sip stack message

debug sip cldu

debug voice verbose

debug int fxs

debug isdn L2-formatted

Thanks for posting!

David

Highlighted
New Contributor III

Thank you.

On Mon, Apr 9, 2012 at 2:47 PM, david

Highlighted
Valued Contributor
Valued Contributor

Meyerj66,

I went ahead and flagged this post as "Assumed Answered".  If any of the responses on this thread assisted you, please mark them as Correct or Helpful as the case may be with the applicable buttons.  This will make them visible and help other members of the community find solutions more easily.  If you still need assistance, I would be more than happy to continue working with you on this - just let me know in a reply.

Thanks!

David