cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 
mtr
New Contributor

Cant connect my adtran 908e to my opensips soft switch

i gave spend many hours to try yo figure this out

i have an opensips server that i use to sell SIP TRUNK right now i have some Asterisk, freeswitch, Cisco ATA devices that are connected to this switch. i got a customer that has a panasonic PBX with a T1 interface so i went ahead and bought the 908e 2nd generation i spend many hour configuring it i couldnt get it to work it was sending the wrong info so i was not able to Auth the outbound calls

finally i got it to register and right now i am getting server 501 on my opensips this is the error from my logfile

/usr/sbin/opensips[24112]: ERROR:core:parse_sip_msg_uri: bad uri <sip:3476783993@68.68.120.146:5060:5060>

so i went ahead and removed all the 5060 that i saw in the web gui and i am still seeing the error line with the 5060 twice

this device is sitting on the local network behind a router

this is my config file

!

!

hostname "TA908e"

enable password xxxxxxxx

!

!

clock timezone -5-Eastern-Time

!

ip subnet-zero

ip classless

ip default-gateway 192.168.2.1

ip routing

ipv6 unicast-routing

!

!

name-server 8.8.8.8 192.168.2.249

!

!

no auto-config

!

event-history on

no logging forwarding

no logging email

!

no service password-encryption

!

username "admin" password "xxxxxxxxx"

!

!

no ip firewall alg msn

no ip firewall alg mszone

no ip firewall alg h323

!

!

!

!

!

!

!

!

no dot11ap access-point-control

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

interface eth 0/1

  ip address  192.168.2.60  255.255.255.0

  no awcp

  no shutdown

  media-gateway ip primary

!

!

interface eth 0/2

  no ip address

  no awcp

  no shutdown

!

!

!

!

interface t1 0/1

  description PRI to PBX 2

  tdm-group 2 timeslots 1-24 speed 64

  no shutdown

!

interface t1 0/2

  no shutdown

!

interface t1 0/3

  no shutdown

!

interface t1 0/4

  tdm-group 1 timeslots 1-24 speed 64

  no shutdown

!

!

interface pri 1

  description pri 1

  isdn name-delivery setup

  connect t1 0/4 tdm-group 1

  no shutdown

!

!

interface fxs 0/1

  no shutdown

!

interface fxs 0/2

  no shutdown

!

interface fxs 0/3

  no shutdown

!

interface fxs 0/4

  no shutdown

!

interface fxs 0/5

  no shutdown

!

interface fxs 0/6

  no shutdown

!

interface fxs 0/7

  no shutdown

!

interface fxs 0/8

  no shutdown

!

!

interface fxo 0/0

  no shutdown

!

!

isdn-group 1

  connect pri 1

!

!

!

!

!

!

!

!

!

!

!

ssh-server 223

no tftp server

no tftp server overwrite

http server 82

http secure-server 445

no snmp agent

no ip ftp server

no ip scp server

no ip sntp server

!

!

!

!

!

!

!

!

sip

sip udp 5060

no sip tcp

!

!

!

voice feature-mode network

voice forward-mode network

!

!

!

!

!

!

!

!

voice dial-plan 1 local NXX-XXX-XXXX

voice dial-plan 2 long-distance 1-NXX-XXX-XXXX

!

!

!

!

!

!

voice trunk T01 type sip

  Description "DPhone"

  sip-server primary sip.xxxxx.cloud

  domain "108.58.25.30"

  sip-keep-alive options 30

  codec-list Trunks both

  no diversion-supported

 

voice trunk T02 type isdn

  resource-selection circular descending

  connect isdn-group 1

  no early-cut-through

  t38

  rtp delay-mode adaptive

!

!

voice grouped-trunk PRI

  trunk T02

  accept $ cost 0

!

!

voice grouped-trunk SIP

  trunk T01

  accept $ cost 0

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

line con 0

  login

!

line telnet 0 4

  login

  no shutdown

line ssh 0 4

  login local-userlist

  no shutdown

!

!

!

!

!

end

Tags (2)
0 Kudos
2 Replies
jwable
Contributor III
Contributor III

Re: Cant connect my adtran 908e to my opensips soft switch

Option 501 errors are not always error messages.  They are a keep alive message that keeps the ports open and registration established.  If you are seeing the messages but calls are woring normally the message can be ignored.  If calls are not working normally then we will need to see the output of debug sip stack messages and debug voice verbose from the Adtran during a call.  Also I see where you have the Domain command on the SIP Trunk but no Grammer Statements telling the how to use it, so if the Adtran is not able to register or make calls you may want to try adding the following to the config:

ip sip grammar from host domain

ip sip grammar to host domain

If your Softswitch requires registration you have to add it to your trunk as well, if using IP based trust then the current config should be fine.  Add the following to your Voice Trunk T01 to add registration:

registrar primary sip.xxxxx.cloud

register UsernameHere auth-name "UsernameHere" password "PasswordHere"

authentication username "UsernameHere" password "PasswordHere"

John Wable

yredovich
New Contributor III

Re: Cant connect my adtran 908e to my opensips soft switch

I would do "debug sip stack messages" using the Adtran CLI and see if the URI sent from the Adtran does indeed list the port twice. Based on the config you provided - it shouldn't. Running the debug will help you determine which device to troubleshoot next:

If you see the 5060 port listed twice in the debug, then I would try a different code version. I'm running R12.3.2.E on TA900eG2 and haven't had issues like this, so you may want to give it a shot.

If the debug only shows the port once, then I would look at the soft switch config. There could be a header manipulation rule that adds the port, before the SIP parser goes to work.

Hope this helps

Yan.