Adtran
Help
The Adtran community holiday season is starting next week! The holiday period will span from December 21, 2024 to January 6, 2025. During this time, responses to feedback form submissions may be delayed. If you are encountering product issues, you can reach out to Adtran support at any time.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Show  only  | Search instead for 
Did you mean: 
manojkumar305
New Contributor
‎08-16-2012 02:05 PM

PRI to Cisco CME

Jump to solution

We are having issues with keep the PRI circuit up

Adtran 908e is intermittent, tried to use the alternative T1 options on Adtran 908e, same results.

Clock jumps from line to internal and when it goes to internal, it goes down. Relevant configuration below - any help is appreciated

!

interface t1 0/4

  description Skybeam PRI

  fdl att

  tdm-group 1 timeslots 1-24 speed 64

  no shutdown

!

!

interface pri 1

  description pri 1

  isdn name-delivery display

  connect t1 0/4 tdm-group 1

  role network b-channel-restarts disable

  no shutdown

!

!

isdn-group 1

  connect pri 1

!

voice trunk T01 type sip

  description "JKHKHKHK"

  match dnis "XNXX-NXX-XXXX" substitute "011XNXX-NXX-XXXX"

  sip-server primary x.x.x.x

  no registrar require-expires

!

voice trunk T02 type isdn

  description "Cisco"

  resource-selection linear ascending

  connect isdn-group 1

  early-cut-through

  modem-passthrough

  vad

  no nls

  rtp delay-mode adaptive

!

!

voice grouped-trunk SIP

  trunk T01

  accept $ cost 0

  accept NXX-NXX-XXXX cost 0

  accept 011-$ cost 0

  reject NXX-976-XXXX

!

!

voice grouped-trunk PRI

  trunk T02

  accept $ cost 0

!

Labels (1)
Labels
Tags (4)
0 Kudos
Reply
1 Solution

Accepted Solutions
Anonymous
Not applicable
‎08-20-2012 02:25 PM

Re: PRI to Cisco CME

Jump to solution

Manojkumar,

Thanks for posting!  Any automatic timing change in the unit is the result of the timing source being lost, or the T-1 going down in this case.  Generally speaking, the T-1 clock for the Total Access 900 series units should synchronize to a carrier-facing T-1 or be set to internal if the unit has an Ethernet port facing the carrier.  The Cisco CME should be set to synchronize its clock to the T-1 clock it receives from the Adtran unit.  Typically this would be called "line" or "network" timing on the PBX.

You should first always verify that T-1 framing and coding settings match up.  Then verify the timing settings above.  If you take errors on the Adtran unit, we would typically plug the port into a loopback adapter to verify the port runs without errors to itself.  If it takes errors when connected to the Cisco, you may want to attempt to adjust the LBO settings on that port.  Below is an example.

interface t1 0/3

  lbo long -15

It is rare, but occasionally I see this attenuation help clear up synchronization issues on the connected device.  If you are unable to prevent the PBX from dropping the T-1 or sending an alarm of some kind, we would be glad to assist you further.  However, you may need to place a T-1 test set between the two units to check for problems with voltage or frequency.  In particular, I would check the frequency the Adtran unit is sending out and verify the PBX is sending back T-1 framing at that same frequency.

Thanks,

David

View solution in original post

Reply
2 Replies
Anonymous
Not applicable
‎08-20-2012 02:25 PM

Re: PRI to Cisco CME

Jump to solution

Manojkumar,

Thanks for posting!  Any automatic timing change in the unit is the result of the timing source being lost, or the T-1 going down in this case.  Generally speaking, the T-1 clock for the Total Access 900 series units should synchronize to a carrier-facing T-1 or be set to internal if the unit has an Ethernet port facing the carrier.  The Cisco CME should be set to synchronize its clock to the T-1 clock it receives from the Adtran unit.  Typically this would be called "line" or "network" timing on the PBX.

You should first always verify that T-1 framing and coding settings match up.  Then verify the timing settings above.  If you take errors on the Adtran unit, we would typically plug the port into a loopback adapter to verify the port runs without errors to itself.  If it takes errors when connected to the Cisco, you may want to attempt to adjust the LBO settings on that port.  Below is an example.

interface t1 0/3

  lbo long -15

It is rare, but occasionally I see this attenuation help clear up synchronization issues on the connected device.  If you are unable to prevent the PBX from dropping the T-1 or sending an alarm of some kind, we would be glad to assist you further.  However, you may need to place a T-1 test set between the two units to check for problems with voltage or frequency.  In particular, I would check the frequency the Adtran unit is sending out and verify the PBX is sending back T-1 framing at that same frequency.

Thanks,

David

Reply
manojkumar305
New Contributor
‎08-20-2012 06:18 PM

Re: PRI to Cisco CME

Jump to solution

I actually tried this on Friday and got it to work.

0 Kudos
Accept as Solution Reply