cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 
Anonymous
Not applicable

Star Codes not working on Adtran TA908

Jump to solution

Customer had their IT people swap out their phones and equipment on their half PRI and pots lines. Before the change out, they were able to use *72 just fine to forward their pots line to an answering service. After the equipment change out, they called us with some issues calling out. After making a few workaround changes on the Adtran, it worked just fine. They were unable to call 911 and had to make an entry for that too. Now, when they try to dial *72 to invoke call forwarding, they get an error message that the number cannot be completed as dialed. Tech tried directly off of the punch down block and are still getting an error message that the call cannot be completed as dialed. Is there something I am missing that will allow the star codes to pass through to the switch? Attached is the current configuration.

0 Kudos
1 Solution

Accepted Solutions
Anonymous
Not applicable

Re: Star Codes not working on Adtran TA908

Jump to solution

I wanted to provide the solution that resolved our issue. Come to find out, we just need to add a line

isdn switch-type 5ess

to be compatible with the unit the phone equipment vendor had installed. Once we did that star codes are working as they should. Thank you to all that assisted in their comments.

View solution in original post

0 Kudos
11 Replies
shambler
New Contributor II

Re: Star Codes not working on Adtran TA908

Jump to solution

On voice grouped-trunk T01 I would suggest adding the following

accept *X$

Anonymous
Not applicable

Re: Star Codes not working on Adtran TA908

Jump to solution

Thanks shambler for your reply. I added that and we still get the same message that you call cannot be completed as dialed.

Anonymous
Not applicable

Re: Star Codes not working on Adtran TA908

Jump to solution

Have you tried adding SPRE codes?

https://supportforums.adtran.com/docs/DOC-2875

shambler
New Contributor II

Re: Star Codes not working on Adtran TA908

Jump to solution

can you attach updated config with additional accept statement

Also gather following debugs

debug int fxs

debug voice verbose

debug sip stack messages

Anonymous
Not applicable

Re: Star Codes not working on Adtran TA908

Jump to solution

When I try to add the SPRE code is says "%SPRE code already mapped to Call last dialed number".

Anonymous
Not applicable

Re: Star Codes not working on Adtran TA908

Jump to solution

You will find the current config attached as well as the debug logs. On the debug logs another call came in right as we were testing so you may have to sort through that other data. Logs begin where she was trying *73 to deactivate Call Forward Always.

shambler
New Contributor II

Re: Star Codes not working on Adtran TA908

Jump to solution

the *73 originating from FXS 0/5 egresses ok out the T01 trunk to voip.lighttube.net

If that generates an error that is coming from the carrier level.

no *72 events detected in debug

If there was a *72 event from the customer did that originate from the PRI connection? if so I also noticed no *X$ ISDN trunk T02

Anonymous
Not applicable

Re: Star Codes not working on Adtran TA908

Jump to solution

We did not have the customer do *72 wince she does not want to activate the CFA. We test with *73 which will bring up the announcement that the CFA has been deactivated.

Anonymous
Not applicable

Re: Star Codes not working on Adtran TA908

Jump to solution

I added the accept *X$ to the T02 and then had them test. Still not working, I've included the debug. I'm starting to think this is a carrier issue.

shambler
New Contributor II

Re: Star Codes not working on Adtran TA908

Jump to solution

no SIP debug on it but yea appears to be carrier.

Perhaps no call forward variable provisioned on individual line 9314552005

From your last debug gathering it showed call being answered, so the recording is coming from the carrier level

09:15:48.871 SIP.STACK MSG Rx: UDP src=209.209.172.231:5060 dst=10.18.216.10:5060

09:15:48.872 SIP.STACK MSG     SIP/2.0 200 OK
09:15:48.873 SIP.STACK MSG     From: "Marvel MainLine" <sip:9314552005@voip.lighttube.net:5060;transport=UDP>;tag=2a1fe08-7f000001-13c4-1552a-7aa937aa-1552a
09:15:48.873 SIP.STACK MSG     To: <sip:*73@voip.lighttube.net:5060>;tag=1299664383-1486134948829
09:15:48.874 SIP.STACK MSG     Call-ID: 2a47310-7f000001-13c4-1552a-55f469ce-1552a@voip.lighttube.net
09:15:48.875 SIP.STACK MSG     CSeq: 2 INVITE
09:15:48.875 SIP.STACK MSG     Via: SIP/2.0/UDP 10.18.216.10:5060;branch=z9hG4bK-1552a-534af03-2fb9dde0
09:15:48.876 SIP.STACK MSG     Allow: ACK,BYE,CANCEL,INFO,INVITE,OPTIONS,PRACK,REFER,NOTIFY,UPDATE
09:15:48.877 SIP.STACK MSG     Supported:
09:15:48.877 SIP.STACK MSG     Accept: application/media_control+xml,application/sdp
09:15:48.878 SIP.STACK MSG     Contact: <sip:*73@209.209.172.231:5060;transport=udp>
09:15:48.879 SIP.STACK MSG     Call-Info: <sip:172.16.6.141>;appearance-index=1
09:15:48.879 SIP.STACK MSG     Content-Type: application/sdp
09:15:48.880 SIP.STACK MSG     Content-Length: 150
09:15:48.880 SIP.STACK MSG
09:15:48.881 SIP.STACK MSG     v=0
09:15:48.882 SIP.STACK MSG     o=BroadWorks 55660592 1 IN IP4 209.209.172.231
09:15:48.882 SIP.STACK MSG     s=-
09:15:48.883 SIP.STACK MSG     c=IN IP4 209.209.172.231
09:15:48.883 SIP.STACK MSG     t=0 0
09:15:48.884 SIP.STACK MSG     m=audio 64674 RTP/AVP 0
09:15:48.885 SIP.STACK MSG     a=rtpmap:0 PCMU/8000
09:15:48.886 SIP.STACK MSG     a=ptime:20
Anonymous
Not applicable

Re: Star Codes not working on Adtran TA908

Jump to solution

I wanted to provide the solution that resolved our issue. Come to find out, we just need to add a line

isdn switch-type 5ess

to be compatible with the unit the phone equipment vendor had installed. Once we did that star codes are working as they should. Thank you to all that assisted in their comments.

0 Kudos